Build it step by step
0 of 8 doneCheck the probe
Attach the probe to the scope's calibration output and set the 10x setting.
Build the 555
Wire the astable on the breadboard.
Connect the probe
Clip the ground first, then touch pin 3.
Set the vertical scale
Use 2 V per division.
Set the time base
Use 0.5 ms per division and trigger on the rising edge.
Measure the period
Count divisions between rising edges and work out the frequency.
Measure the duty cycle
Compare high time with the period.
Compare with the calculation
Check against 690 Hz and 52 percent.
How do you build an oscilloscope first steps?
Use a scope to see a 555 square wave, measure frequency and duty cycle and trigger properly. You need Digital oscilloscope 2-channel 100 MHz, NE555 Timer IC, Resistor 1 kΩ, Resistor 10 kΩ, Ceramic Capacitor 100 nF, Breadboard 830 Tie Points, 9 V battery and 9 V battery snap with DC jack. It takes 8 steps and about 60 minutes.
- Level
- Intermediate
- Time
- About 60 min
- Parts
- 8
Parts list
- Tools & InstrumentsBuy
- Integrated CircuitsBuyNE555 Timer IC × 1
- PassivesBuyResistor 1 kΩ × 1
- PassivesBuyResistor 10 kΩ × 1
- PassivesBuy
- PrototypingBuy
- BatteriesBuy9 V battery × 1
- PowerBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| 9 V battery + | + rail | Supply |
| 9 V battery - | - rail | Ground |
| 555 pin 8 and pin 4 | + rail | Power and reset high |
| 555 pin 1 | - rail | Ground |
| 1 kΩ resistor R1 | + rail and 555 pin 7 | Timing |
| 10 kΩ resistor R2 | 555 pin 7 and pin 6 | Timing |
| 555 pins 2 and 6 | Joined | Astable connection |
| 100 nF capacitor | 555 pin 6 and - rail | Timing capacitor, about 690 Hz |
| Scope probe tip | 555 pin 3 | Output signal |
| Scope probe ground clip | - rail | Ground reference |
No code needed
No code. The 555 should give about f = 1.44 ÷ ((1 kΩ + 2 × 10 kΩ) × 100 nF) = 690 Hz, a period of about 1.46 ms, with a duty cycle of (R1 + R2) ÷ (R1 + 2 R2) = 52 percent. Set the probe to 10x on the probe and the scope to match. Always connect the ground clip first, to the circuit ground, and do not clip it to a point at a different voltage. The scope's ground is usually the mains earth, so never connect the clip to mains-connected circuits. A good start is 2 V per division and 0.5 ms per division, triggered on a rising edge at about half the supply voltage.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Frequency | About 690 Hz |
| Duty cycle | About 52 percent |
| Square corners | Slight rounding at higher time scales |
| Trigger set badly | Picture runs across the screen |
If it does not work
Waveform runs
Set the trigger source, edge and level.
Signal looks tiny or huge
Change volts per division and check the 10x setting.
Noisy trace
Check the ground clip is connected and short.
Square wave overshoots
Compensate the probe with the calibration screw.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the oscilloscope first steps?
Digital oscilloscope 2-channel 100 MHz, NE555 Timer IC, Resistor 1 kΩ, Resistor 10 kΩ, Ceramic Capacitor 100 nF, Breadboard 830 Tie Points, 9 V battery and 9 V battery snap with DC jack.
How long does the oscilloscope first steps take to build?
About 60 minutes for a intermediate maker, in 8 steps.
How do I know the oscilloscope first steps works?
Frequency: About 690 Hz. Duty cycle: About 52 percent. Square corners: Slight rounding at higher time scales.
Waveform runs: what should I check?
Set the trigger source, edge and level.
Signal looks tiny or huge: what should I check?
Change volts per division and check the 10x setting.
Noisy trace: what should I check?
Check the ground clip is connected and short.
Square wave overshoots: what should I check?
Compensate the probe with the calibration screw.
