Line follower robot
A two-wheel robot follows a black line on a white floor using two IR reflective sensors and an L298N motor driver.
Build it step by step
0 of 6 doneBuild the chassis
Fit both motors, the wheels and the caster. Mount the Uno and the L298N on top with spacers.
Mount the sensors
Fix both sensors at the front, about 1 cm above the floor and 2 to 3 cm apart, so the line (about 2 cm wide) fits between them.
Wire the motors
Left motor to OUT1/OUT2, right motor to OUT3/OUT4. Remove the ENA and ENB jumpers and wire the driver pins to the Uno.
Wire power
Battery through the switch to the L298N 12V terminal and the Uno VIN. Join all grounds.
Set the sensors
Power up, hold each sensor over white and then black tape, and turn its trimmer until the module LED changes exactly at the edge.
Upload and test
Lift the wheels, upload, cover each sensor with black tape and check each wheel's direction. Then run it on a taped loop.
How do you build a line follower robot?
A two-wheel robot follows a black line on a white floor using two IR reflective sensors and an L298N motor driver. You need Arduino Uno R3, L298N Dual H-Bridge Module, TCRT5000 IR reflective sensor module × 2, Robot car chassis kit 2WD (acrylic), Battery holder 18650 2S (series), 18650 cell 2600 mAh (branded) × 2, Rocker switch (KCD1, 2-pin) and Jumper wires male to female (40 pcs). It takes 6 steps and about 120 minutes.
- Level
- Intermediate
- Time
- About 120 min
- Parts
- 8
Parts list
- Development BoardsBuyArduino Uno R3 × 1
- Motor DriversBuy
- SensorsBuy
- Mechanical & HardwareBuyComes with two BO motors, wheels and a caster
- PowerBuy
- BatteriesBuyCharge them with a proper Li-ion charger
- SwitchesBuy
- PrototypingBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| Battery + (through the rocker switch) | L298N 12V terminal and Uno VIN | Power for motors and board |
| Battery − | L298N GND and Uno GND | One shared ground |
| L298N OUT1 / OUT2 | Left motor | Left wheel |
| L298N OUT3 / OUT4 | Right motor | Right wheel |
| L298N ENA / ENB | Uno D5 / D6 (remove the ENA and ENB jumpers) | Speed by PWM |
| L298N IN1 / IN2 / IN3 / IN4 | Uno D7 / D8 / D9 / D10 | Direction |
| Left sensor DO / Right sensor DO | Uno A0 / A1 | Line readings (used as digital pins) |
| Sensor VCC / GND | Uno 5V / GND | Sensor power |
Code
Arduino IDE, board "Arduino Uno". No extra libraries. If the robot turns away from the line, change BLACK to LOW.
Runs on a virtual Arduino Uno in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).
const int ENA = 5, IN1 = 7, IN2 = 8, IN3 = 9, IN4 = 10, ENB = 6;
const int LEFT = A0, RIGHT = A1;
const int BLACK = HIGH; // most TCRT5000 modules output HIGH over a black line
const int SPEED = 150, TURN = 120;
void drive(int l, int r) {
digitalWrite(IN1, l >= 0 ? HIGH : LOW); digitalWrite(IN2, l < 0 ? HIGH : LOW);
digitalWrite(IN3, r >= 0 ? HIGH : LOW); digitalWrite(IN4, r < 0 ? HIGH : LOW);
analogWrite(ENA, abs(l)); analogWrite(ENB, abs(r));
}
void setup() {
int outs[] = {ENA, IN1, IN2, IN3, IN4, ENB};
for (int p : outs) pinMode(p, OUTPUT);
pinMode(LEFT, INPUT); pinMode(RIGHT, INPUT);
delay(2000); // time to put the robot on the line
}
void loop() {
bool l = digitalRead(LEFT) == BLACK, r = digitalRead(RIGHT) == BLACK;
if (!l && !r) drive(SPEED, SPEED); // line between the sensors: go straight
else if (l && !r) drive(-TURN, TURN); // line under the left sensor: turn left
else if (!l && r) drive(TURN, -TURN); // line under the right sensor: turn right
else drive(0, 0); // both on black: stop at the end mark
}Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Both sensors over white | Both wheels turn forward at the same speed |
| Left sensor over black | Left wheel reverses, right wheel forward: the robot turns left |
| Both sensors over black | Both wheels stop |
| Battery voltage at the L298N | 7.4 to 8.4 V with fresh 18650 cells |
If it does not work
A wheel turns the wrong way
Swap that motor's two wires at the L298N outputs.
The robot spins in circles
The sensor logic is inverted. Change BLACK to LOW, or adjust the sensor trimmers.
Motors hum but do not move
Raise SPEED, check the ENA/ENB jumpers are removed and the wires go to D5/D6, and charge the cells.
The Uno resets when the motors start
The cells are weak or the wiring is thin. Use good cells and a direct, short ground wire.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the line follower robot?
Arduino Uno R3, L298N Dual H-Bridge Module, TCRT5000 IR reflective sensor module × 2, Robot car chassis kit 2WD (acrylic), Battery holder 18650 2S (series), 18650 cell 2600 mAh (branded) × 2, Rocker switch (KCD1, 2-pin) and Jumper wires male to female (40 pcs). Robot car chassis kit 2WD (acrylic): Comes with two BO motors, wheels and a caster. 18650 cell 2600 mAh (branded) × 2: Charge them with a proper Li-ion charger.
How long does the line follower robot take to build?
About 120 minutes for a intermediate maker, in 6 steps.
How do I know the line follower robot works?
Both sensors over white: Both wheels turn forward at the same speed. Left sensor over black: Left wheel reverses, right wheel forward: the robot turns left. Both sensors over black: Both wheels stop.
A wheel turns the wrong way: what should I check?
Swap that motor's two wires at the L298N outputs.
The robot spins in circles: what should I check?
The sensor logic is inverted. Change BLACK to LOW, or adjust the sensor trimmers.
Motors hum but do not move: what should I check?
Raise SPEED, check the ENA/ENB jumpers are removed and the wires go to D5/D6, and charge the cells.
The Uno resets when the motors start: what should I check?
The cells are weak or the wiring is thin. Use good cells and a direct, short ground wire.
