Projects / Inductor back-EMF lab

Inductor back-EMF lab

Intermediate45 minGuided buildReviewed

Build it step by step

0 of 7 done
  1. ON

    Wire the coil

    Connect the relay coil, the button and the batteries so the relay clicks when pressed.

  2. 12.4 mA

    Add the LED

    Wire the LED and resistor backwards across the coil as in the table.

  3. Press and release

    Watch for a brief flash at the moment of release only.

  4. Look at it on a scope

    If you have one, probe terminal B to ground and see the spike on release.

  5. +

    Add the diode

    Fit the 1N4007 across the coil, cathode to the battery side.

  6. 12.5 mA

    Repeat

    The LED no longer flashes and the spike is gone.

  7. ON

    Compare a coil

    Try the 1 mH inductor in place of the relay and see a smaller spike.

In short

How do you build an inductor back-EMF lab?

Switch off a relay coil and see the voltage spike with a reverse-connected LED, then tame it with a flyback diode. You need Relay 5 V SPDT (sugar cube), Inductor 1 mH, Rectifier Diode 1N4007, LED 5 mm red, Resistor 330 Ω, Tactile push button 6 mm, Battery holder 4 × AA with switch, AA alkaline battery × 3 and Breadboard 830 Tie Points. It takes 7 steps and about 45 minutes.

Level
Intermediate
Time
About 45 min
Parts
9
See the electronics first. This build uses inductor slowing the current. Try an inductor slowing the current in the circuit builder and watch the voltages and currents before you wire it.

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
3 AA cells + (4.5 V, one holder slot bridged with a wire)Relay coil terminal ASupply
Relay coil terminal BButton, then 3 AA cells -Switched side of the coil
Red LED anodeRelay coil terminal B (the button side) via a 330 Ω resistorSpike indicator
Red LED cathodeRelay coil terminal A (the battery + side)Reverse of the normal polarity
1N4007 (later)Cathode to coil terminal A, anode to coil terminal BFlyback diode

No code needed

No code. The LED is connected the opposite way to the supply, so it is reverse-biased while the coil is on and stays dark. When you release the button, the coil current has to go somewhere, and the voltage at terminal B spikes high enough to push a brief current through the LED, which flashes. The spike can reach tens of volts but carries little energy; still, keep your fingers off the coil terminals while switching. Use only 3 AA cells (4.5 V) for a 5 V coil, fitting a wire link in the unused fourth holder slot.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Button pressedRelay clicks and the LED stays dark
Button released, no diodeLED flashes briefly
Button released, with diodeNo flash
Scope on the switch nodeLarge spike without the diode, clamped to about 0.7 V above the supply with it

If it does not work

LED never flashes

Try a bright red LED and a dim room, or check it is reversed relative to the supply.

LED stays lit while pressed

It is the wrong way round. Reverse it.

Relay will not click

Use fresh batteries and check the coil terminals.

Diode makes the relay buzz

It is the wrong way round. The band goes to the supply side.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the inductor back-EMF lab?

Relay 5 V SPDT (sugar cube), Inductor 1 mH, Rectifier Diode 1N4007, LED 5 mm red, Resistor 330 Ω, Tactile push button 6 mm, Battery holder 4 × AA with switch, AA alkaline battery × 3 and Breadboard 830 Tie Points.

How long does the inductor back-EMF lab take to build?

About 45 minutes for a intermediate maker, in 7 steps.

How do I know the inductor back-EMF lab works?

Button pressed: Relay clicks and the LED stays dark. Button released, no diode: LED flashes briefly. Button released, with diode: No flash.

LED never flashes: what should I check?

Try a bright red LED and a dim room, or check it is reversed relative to the supply.

LED stays lit while pressed: what should I check?

It is the wrong way round. Reverse it.

Relay will not click: what should I check?

Use fresh batteries and check the coil terminals.

Diode makes the relay buzz: what should I check?

It is the wrong way round. The band goes to the supply side.