Projects / Fume extractor with interlock

Fume extractor with interlock

Beginner2 hGuided buildReviewed

Build it step by step

0 of 9 done
  1. NANO12DCLM2596

    Set the buck converter

    Connect the 12 V adapter to the LM2596 only and turn the screw until the output reads 5.0 V.

  2. NANOLM2596

    Wire the 5 V rail

    LM2596 output to the Nano 5V and GND pins, with the Nano unplugged from USB.

  3. NANOACS7120.41 A

    Wire the current sensor

    ACS712 VCC to 5V, GND to GND and OUT to A0.

  4. NANOON

    Wire the relays

    IN1 to D7, IN2 to D8, VCC to 5V and GND to GND.

  5. NANOACS712ON0.42 A

    Wire the fan path

    12 V terminal to relay 1 COM, relay 1 NO to the ACS712 IP+, IP- to the fan red wire, fan black wire to the ground terminal.

  6. NANOON10.1 mA

    Wire the tool and the controls

    Relay 2 NO to the strip +, strip - to ground, button D2 to GND, LEDs on D4 and D5.

  7. NANO

    Upload the sketch with everything off

    The monitor says Interlock ready, because the zero point is measured now.

  8. NANO10.1 mA

    Press the button

    The fan starts, and after three seconds the strip and green light switch on.

  9. NANO10.2 mA

    Press the button again

    The strip goes off and the fan keeps running for a minute.

In short

How do you build a fume extractor with interlock?

A work station only lets the tool switch on while the extractor fan is really running. The sketch measures the fan current with an ACS712, so a stuck or unplugged fan keeps the tool off, and it keeps the fan going for a minute after the tool stops to clear the fumes. A 12 V lamp strip stands in for the tool, so it is safe to build and test. You need Arduino Nano, 12 V DC fan 80 mm, ACS712 current sensor module (5 A / 20 A / 30 A), Relay module 2-channel 5 V, 12 V 2 A DC adapter, DC barrel to screw terminal adapter (female), LM2596 Buck Module, 12 V LED strip warm white (5 m, 2835), Tactile push button 6 mm, LED 5 mm red, LED 5 mm green, Resistor 220 Ω × 2, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 9 steps and about 120 minutes.

Level
Beginner
Time
About 120 min
Parts
14

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
12 V adapterScrew terminal adapterThe only 12 V supply
Terminal + and -LM2596 IN+ and IN-Set OUT to 5.0 V with no load first
LM2596 OUT+ and OUT-Nano 5V and GNDPowers the Nano, relay board and ACS712
Terminal +Relay 1 COM and Relay 2 COM12 V into both relay switches
Relay 1 NOACS712 IP+Fan power goes through the current sensor
ACS712 IP-Fan red wireCarries the fan current
Fan black wireTerminal -Completes the fan circuit
Relay 2 NO12 V LED strip +The stand-in tool
LED strip -Terminal -Completes the tool circuit
ACS712 VCC, GND and OUTNano 5V, GND and A0Output is 2.5 V plus 0.185 V per amp
Relay board IN1 and IN2Nano D7 and D8Fan and tool, active LOW
Relay board VCC and GNDNano 5V and GNDCoil power
Start buttonNano D2 and GNDPress to ask for the tool
Green LEDNano D4 through 220 ohms to GNDTool allowed
Red LEDNano D5 through 220 ohms to GNDFan fault or tool off

Code

An interlock is a rule that one thing may only happen while another is true. Here the tool may only run while the extractor fan is really spinning. The sketch does not trust the fan relay, which would still click if the fan were jammed or unplugged. It measures the current instead. The fan's red wire passes through the ACS712 sensor, which sends a voltage to A0 that sits at 2.5 V with no current and moves by 0.185 V for every amp. A small 12 V fan draws about 0.15 to 0.3 A, so the change is small, and the sketch averages 64 readings and measures the zero point at start-up with everything off, which makes it steady and removes the sensor's own offset. When you press the button, the fan relay switches on, and three seconds later, once the fan has reached speed, the sketch checks the current. Only if it is above 0.08 A does the tool relay switch on and the green light come on. If the fan is stopped, the red light blinks and the tool stays off. When you press the button again the tool switches off at once, but the fan keeps running for a minute to clear the fumes, which is called a run-on. The stand-in tool is a 12 V LED strip, so you can test everything safely. Never use this board to switch mains. A real station needs a certified mains controller with its own interlock. Set the LM2596 to 5.0 V with a multimeter before you connect the Nano, and do not press the button while measuring zero.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

const uint8_t BTN = 2;
const uint8_t FAN_RELAY = 7;             // active LOW
const uint8_t TOOL_RELAY = 8;            // active LOW
const uint8_t GREEN = 4;
const uint8_t RED = 5;
const uint8_t SENSE = A0;

const float AMPS_PER_COUNT = 5.0 / 1023.0 / 0.185;   // ACS712 5 A: 185 mV per amp
const float MIN_FAN_AMPS = 0.08;         // below this the fan counts as stopped
const unsigned long RUN_ON = 60000;      // keep the fan on a minute after the tool stops
const unsigned long SPIN_UP = 3000;      // fan needs this long to reach speed

int zeroCounts = 512;
bool toolWanted = false;
bool prevBtn = false;
unsigned long fanOnAt = 0;
unsigned long toolOffAt = 0;
bool fanOn = false;

float fanAmps() {
  long sum = 0;
  for (int i = 0; i < 64; i++) sum += analogRead(SENSE);
  float counts = sum / 64.0;
  return fabs(counts - zeroCounts) * AMPS_PER_COUNT;
}

void setFan(bool on) {
  if (on && !fanOn) fanOnAt = millis();
  fanOn = on;
  digitalWrite(FAN_RELAY, on ? LOW : HIGH);
}

void setup() {
  pinMode(BTN, INPUT_PULLUP);
  pinMode(FAN_RELAY, OUTPUT);
  pinMode(TOOL_RELAY, OUTPUT);
  pinMode(GREEN, OUTPUT);
  pinMode(RED, OUTPUT);
  digitalWrite(FAN_RELAY, HIGH);
  digitalWrite(TOOL_RELAY, HIGH);
  Serial.begin(9600);
  delay(500);
  long sum = 0;                           // measure the zero point with everything off
  for (int i = 0; i < 128; i++) sum += analogRead(SENSE);
  zeroCounts = sum / 128;
  Serial.println(F("Interlock ready, press the button for the tool"));
}

void loop() {
  bool b = (digitalRead(BTN) == LOW);
  if (b && !prevBtn) {
    toolWanted = !toolWanted;
    if (!toolWanted) toolOffAt = millis();
    Serial.println(toolWanted ? F("Tool requested") : F("Tool off, fan will run on"));
  }
  prevBtn = b;

  // The fan runs whenever the tool is wanted, and for a minute afterwards.
  bool needFan = toolWanted || (millis() - toolOffAt < RUN_ON && toolOffAt > 0);
  setFan(needFan);

  bool fanProven = fanOn && millis() - fanOnAt > SPIN_UP && fanAmps() > MIN_FAN_AMPS;
  bool toolAllowed = toolWanted && fanProven;
  digitalWrite(TOOL_RELAY, toolAllowed ? LOW : HIGH);
  digitalWrite(GREEN, toolAllowed);
  bool fault = toolWanted && !fanProven && millis() - fanOnAt > SPIN_UP;
  digitalWrite(RED, fault ? (millis() / 250) % 2 : !toolWanted && fanOn);

  static unsigned long last = 0;
  if (millis() - last > 1000) {
    last = millis();
    Serial.print(F("Fan "));
    Serial.print(fanOn ? F("on ") : F("off "));
    Serial.print(fanAmps(), 2);
    Serial.print(F(" A, tool "));
    Serial.println(toolAllowed ? F("ALLOWED") : F("blocked"));
  }
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual Arduino Nano with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

Interlock ready, press the button for the tool
Fan off 0.03 A, tool blocked

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Power up and waitFan off, strip off, monitor reads 0.00 A
Press the buttonFan starts, then after 3 s the strip is allowed and the green light is on
Fan current in the monitorAbout 0.15 to 0.3 A for an 80 mm fan
Press the button againStrip off at once, fan runs for about 60 seconds
Jam the fan blade with a pencil while it runsThe strip goes off and the red light blinks

If it does not work

Tool never allowed

Measure the fan current; if it is below 0.08 A lower MIN_FAN_AMPS or check the fan runs through the ACS712.

Current reads half an amp with the fan off

The sensor was powered while measuring zero, so restart the Nano with the fan wires connected but off.

Readings jump around

Keep the signal wire from A0 away from the relay and fan wires.

Relays work the wrong way round

Your board switches on with HIGH, so swap the HIGH and LOW writes.

Nano resets when the relays click

Add a 100 uF capacitor across the Nano power and keep the converter wires short.

Upload fails

Choose the Old Bootloader option for the Nano.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the fume extractor with interlock?

Arduino Nano, 12 V DC fan 80 mm, ACS712 current sensor module (5 A / 20 A / 30 A), Relay module 2-channel 5 V, 12 V 2 A DC adapter, DC barrel to screw terminal adapter (female), LM2596 Buck Module, 12 V LED strip warm white (5 m, 2835), Tactile push button 6 mm, LED 5 mm red, LED 5 mm green, Resistor 220 Ω × 2, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).

How long does the fume extractor with interlock take to build?

About 120 minutes for a beginner maker, in 9 steps.

How do I know the fume extractor with interlock works?

Power up and wait: Fan off, strip off, monitor reads 0.00 A. Press the button: Fan starts, then after 3 s the strip is allowed and the green light is on. Fan current in the monitor: About 0.15 to 0.3 A for an 80 mm fan.

Tool never allowed: what should I check?

Measure the fan current; if it is below 0.08 A lower MIN_FAN_AMPS or check the fan runs through the ACS712.

Current reads half an amp with the fan off: what should I check?

The sensor was powered while measuring zero, so restart the Nano with the fan wires connected but off.

Readings jump around: what should I check?

Keep the signal wire from A0 away from the relay and fan wires.

Relays work the wrong way round: what should I check?

Your board switches on with HIGH, so swap the HIGH and LOW writes.