Projects / Make a set of clip test leads

Make a set of clip test leads

Beginner1.5 hGuided buildReviewed

Build it step by step

0 of 8 done
  1. SILICO4.98V4.98V

    Cut the wire

    Four pieces of 30 cm.

  2. HEAT4.98V

    Slide on the tubing

    Before soldering, 20 mm per end.

  3. SILICO4.98V4.98V

    Strip and tin

    About 5 mm of bare wire.

  4. 4.98V

    Solder to the clip

    Let the solder flow into the joint.

  5. HEAT4.98V

    Cool and cover

    Wait 10 seconds then shrink the tubing.

  6. Pull test

    A firm tug on each end.

  7. Check continuity

    Meter beeps, under 1 ohm.

  8. 4.98V

    Label the set

    Red and black pairs stay together.

In short

How do you build a make a set of clip test leads?

Cut, solder and cover a set of four flexible leads with clips, so you have good test wires at the bench for low-voltage work. You need Silicone wire 22 AWG (assorted colours), Multimeter probes with clips, Heat shrink tubing assortment, Lead-free solder wire (SAC305), Side cutter (flush), Wire stripper and cutter and Digital multimeter. It takes 8 steps and about 90 minutes.

Level
Beginner
Time
About 90 min
Parts
7

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Clip tail (crimp tabs or solder cup)Tinned 22 AWG silicone wire end, 5 mmSolder joint, strands fully wetted
Silicone wire30 cm length, black for ground and red for positiveColour code stays the same on every lead
Wire far endSecond clip or probe tipSame joint as the first end
Each joint20 mm heat shrink slid on before solderingCovers the joint and grips the insulation
Finished leadMultimeter continuity beep, end to endProves the lead is complete

Code

Good test leads make every other build easier, and a home-made set is a great first soldering and heat-shrink job. Silicone wire is a good choice because it is very flexible and does not melt if the iron touches it. The most common mistake is forgetting to slide the heat shrink on before soldering, because you cannot add it afterwards. Strip a few millimetres, twist the strands and tin them. Then solder the strands into the clip so the solder flows into the joint and makes it bright and smooth. A dull, grainy joint, called a cold joint, can look fine and still fail later. After the joint cools without being moved, slide the heat shrink over and shrink it. Colour coding matters: use red for positive and black for ground on every lead, so that a quick glance at the bench tells you which wire is which. Finish with a pull test and a continuity test: the meter should beep and read well below one ohm, and the two leads should not read as connected to each other. These leads are for low-voltage bench work only and are not safe for mains.

Build notes (no code needed for this build)

Use: low-voltage bench work only, such as batteries, USB power and logic circuits up to 30 V. These leads are NOT rated for mains. Never use home-made leads on mains wiring.

Lead specification
  Wire         : 22 AWG silicone, flexible and heat resistant
  Length       : 30 cm
  Count        : four leads, two red and two black, plus any other colours you like
  Current      : fine for a few amps in short bursts; use thicker wire for sustained high current

Method
 1. Cut four lengths of 30 cm with the side cutter.
 2. Slide a 20 mm piece of heat shrink onto each wire end BEFORE you solder. Push it back out of the heat.
 3. Strip about 5 mm, twist the strands and tin them with a little solder.
 4. Push the tinned end into the solder cup or through the crimp tab of the clip, then reheat so the solder flows into the joint. A good joint is bright and smooth.
 5. Let each joint cool for about 10 seconds without moving it.
 6. Slide the heat shrink over the joint and shrink it with a hot air tool on low, or run the shaft of the iron along it. Keep the wire away from open flame.
 7. Pull test each lead with a firm tug, then check continuity with the meter: it should beep, and the meter should read under 1 ohm.
 8. Check that neither end is shorted to the other lead.

Soldering safety: the iron runs at about 350 degrees C. Use a stand, work in a ventilated space, and wash your hands after handling solder.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Continuity, end to endBeep and under 1 ohm
Pull testJoint does not move
Between two different leadsNo beep, no connection
Joint appearanceBright, smooth and wetted
Colour checkRed and black on every pair

If it does not work

Joint is dull and grainy

Reheat and add a little fresh solder, hold still while it cools.

Tubing does not fit

It must be slid on before soldering.

No beep

Reheat the joint or recheck the stripped strands.

Strands poke out

Twist them tightly and trim any stray ones.

Wire insulation melted

The iron touched it, let it cool and recut.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the make a set of clip test leads?

Silicone wire 22 AWG (assorted colours), Multimeter probes with clips, Heat shrink tubing assortment, Lead-free solder wire (SAC305), Side cutter (flush), Wire stripper and cutter and Digital multimeter.

How long does the make a set of clip test leads take to build?

About 90 minutes for a beginner maker, in 8 steps.

How do I know the make a set of clip test leads works?

Continuity, end to end: Beep and under 1 ohm. Pull test: Joint does not move. Between two different leads: No beep, no connection.

Joint is dull and grainy: what should I check?

Reheat and add a little fresh solder, hold still while it cools.

Tubing does not fit: what should I check?

It must be slid on before soldering.

No beep: what should I check?

Reheat the joint or recheck the stripped strands.

Strands poke out: what should I check?

Twist them tightly and trim any stray ones.