Projects / Breadboard power hub

Breadboard power hub

Beginner1.5 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. LM2596

    Set the buck

    Trim to 5.0 V with no load.

  2. AMS11174.85 V

    Wire the linear regulator

    AMS1117 from the 5 V rail.

  3. Add the polyfuses

    One per output.

  4. 17.9 mA

    Add power LEDs

    Resistor and LED on each rail.

  5. AMS1117SCREW4.86 V

    Add the capacitors

    At each regulator pin.

  6. AMS1117SCREW4.86 V

    Fit the terminals

    Label voltage and polarity.

  7. Test with a short

    Briefly short a rail and watch the fuse cut off.

In short

How do you build a breadboard power hub?

A board that gives 3.3 V, 5 V and 12 V rails with fuses and on lights from one adapter. You need 12 V 2 A DC adapter, LM2596 Buck Module, AMS1117 Voltage Regulator, Polyfuse (PTC resettable) 500 mA × 3, LED 5 mm red × 3, Resistor 1 kΩ × 3, Screw terminal block 2-pin (5 mm) × 3, Perfboard (dot PCB) 7 × 9 cm, Electrolytic capacitor 10 µF × 3 and Ceramic Capacitor 100 nF × 3. It takes 7 steps and about 90 minutes.

Level
Beginner
Time
About 90 min
Parts
10

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
12 V adapter plus12 V rail, through a 500 mA polyfuse12 V output
12 V railLM2596 input plusBuck input
LM2596 output (set to 5.0 V first)5 V rail, through a 500 mA polyfuse5 V output
5 V railAMS1117 inputLinear regulator
AMS1117 output3.3 V rail, through a 500 mA polyfuse3.3 V output
Each output rail1 kΩ then red LED to groundPower-on light
Decoupling10 µF and 100 nF at each regulator input and outputStable rails
Each rail and groundA 2-pin screw terminalLabelled outputs

No code needed

Set the LM2596 to exactly 5.0 V with its trim pot and a multimeter before connecting anything to the board; do this with no load. The AMS1117 then makes 3.3 V from the 5 V rail, which is gentler than dropping from 12 V, since a linear regulator wastes the difference as heat; at 300 mA it drops 1.7 V, about half a watt, which is fine. Each rail has a 500 mA resettable polyfuse, which heats up and cuts the current on a short, then recovers when the fault is removed, and a power LED so you know which rails are live. Add the 10 µF and 100 nF capacitors at the regulator pins; without them regulators can oscillate. Label every terminal with its voltage in large letters, because plugging a 12 V rail into a 3.3 V board destroys it. Use a 12 V adapter of known good quality, and never connect it to mains wiring yourself.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
5 V rail5.0 V within 0.1 V
3.3 V rail3.3 V within 0.1 V
Short on a railPolyfuse cuts off, others stay on
HeatRegulators warm, not hot

If it does not work

5 V not stable

Check the buck setting and decoupling.

3.3 V low

Check the AMS1117 pin order.

Polyfuse trips on normal load

Use a higher rating or reduce the load.

LED dim

Check the 1 kΩ values.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the breadboard power hub?

12 V 2 A DC adapter, LM2596 Buck Module, AMS1117 Voltage Regulator, Polyfuse (PTC resettable) 500 mA × 3, LED 5 mm red × 3, Resistor 1 kΩ × 3, Screw terminal block 2-pin (5 mm) × 3, Perfboard (dot PCB) 7 × 9 cm, Electrolytic capacitor 10 µF × 3 and Ceramic Capacitor 100 nF × 3.

How long does the breadboard power hub take to build?

About 90 minutes for a beginner maker, in 7 steps.

How do I know the breadboard power hub works?

5 V rail: 5.0 V within 0.1 V. 3.3 V rail: 3.3 V within 0.1 V. Short on a rail: Polyfuse cuts off, others stay on.

5 V not stable: what should I check?

Check the buck setting and decoupling.

3.3 V low: what should I check?

Check the AMS1117 pin order.

Polyfuse trips on normal load: what should I check?

Use a higher rating or reduce the load.

LED dim: what should I check?

Check the 1 kΩ values.