Projects / Automatic plant watering system

Automatic plant watering system

Beginner1.3 hGuided buildReviewed

Build it step by step

0 of 5 done
  1. UNOCAPACITI29.4°C

    Calibrate the sensor

    Upload, push the sensor into dry soil up to the line and note the reading. Water the pot, wait a minute and note it again. Put those numbers in DRY and WET.

  2. UNOONSILICO

    Wire the relay

    VCC, GND and IN to D7. Check the relay clicks once at start-up.

  3. UNOONSILICO29.4°C

    Wire the pump

    AA pack plus to relay COM, relay NO to the pump plus, pump minus back to the pack minus.

  4. UNO29.4°C

    Place the pump

    Put the pump in a water container and run its tube to the pot. Never run it dry.

  5. UNO29.4°C

    Run and watch

    Upload the calibrated sketch and watch the serial monitor through one watering cycle.

In short

How do you build an automatic plant watering system?

A capacitive soil sensor checks the pot and a relay runs a small pump for a few seconds whenever the soil is dry. You need Arduino Uno R3, Capacitive Soil Moisture Module, Relay Module 5V, Mini submersible water pump (3 to 6 V), Battery holder 4 × AA with switch, AA alkaline battery × 4, Silicone wire 22 AWG (assorted colours) and Jumper wires male to female (40 pcs). It takes 5 steps and about 75 minutes.

Level
Beginner
Time
About 75 min
Parts
8

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Soil sensor VCC / GNDUno 5V / GNDSensor power
Soil sensor AOUTUno A0Moisture reading (higher = drier)
Relay VCC / GND / INUno 5V / GND / D7Relay control
AA pack +Relay COMPump supply goes through the relay
Relay NOPump + (red)Pump runs only when the relay closes
Pump −AA pack −Pump return

Code

Arduino IDE, board "Arduino Uno". No extra libraries. Calibrate DRY and WET with your own soil before leaving it running.

Runs on a virtual Arduino Uno in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

const int SENSOR = A0, RELAY = 7;
const int DRY = 520, WET = 430;          // calibrate: reading in dry and in just-watered soil
const unsigned long PUMP_MS = 3000, SOAK_MS = 60000;
const bool RELAY_ON = LOW;               // most relay modules switch on with LOW

void setup() {
  pinMode(RELAY, OUTPUT); digitalWrite(RELAY, !RELAY_ON);
  Serial.begin(9600);
}

void loop() {
  int raw = analogRead(SENSOR);
  Serial.print("soil="); Serial.println(raw);
  if (raw > DRY) {
    Serial.println("Dry: watering");
    digitalWrite(RELAY, RELAY_ON); delay(PUMP_MS);
    digitalWrite(RELAY, !RELAY_ON);
    delay(SOAK_MS);                      // let the water soak in before reading again
  } else if (raw < WET) {
    delay(10000);                        // wet enough: check again in 10 s
  } else {
    delay(5000);
  }
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual Arduino Uno with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

soil=512
soil=513

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Sensor in airAbout 550 to 620
Sensor in water up to the lineAbout 250 to 320
Dry soil"Dry: watering", relay clicks, pump runs for 3 s
Just after wateringNo more watering for at least 60 s

If it does not work

The pump runs all the time

Your relay may switch on with HIGH. Change RELAY_ON to HIGH.

Readings jump around

Push the sensor to the same depth each time and keep the electronics above the line dry.

The pump hums but no water

Prime it under water and check the tube is not kinked.

Watering every minute

DRY is too low for your soil. Recalibrate.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the automatic plant watering system?

Arduino Uno R3, Capacitive Soil Moisture Module, Relay Module 5V, Mini submersible water pump (3 to 6 V), Battery holder 4 × AA with switch, AA alkaline battery × 4, Silicone wire 22 AWG (assorted colours) and Jumper wires male to female (40 pcs).

How long does the automatic plant watering system take to build?

About 75 minutes for a beginner maker, in 5 steps.

How do I know the automatic plant watering system works?

Sensor in air: About 550 to 620. Sensor in water up to the line: About 250 to 320. Dry soil: "Dry: watering", relay clicks, pump runs for 3 s.

The pump runs all the time: what should I check?

Your relay may switch on with HIGH. Change RELAY_ON to HIGH.

Readings jump around: what should I check?

Push the sensor to the same depth each time and keep the electronics above the line dry.

The pump hums but no water: what should I check?

Prime it under water and check the tube is not kinked.

Watering every minute: what should I check?

DRY is too low for your soil. Recalibrate.