4-bit R-2R ladder D/A converter
To build a 4-bit R-2R ladder DAC with an op-amp and measure its output for every input code, its resolution and accuracy.
- IC 741
- Resistors 10 kΩ and 20 kΩ (1%)
- Switches or an Arduino for the 4 bits
- DC reference 5 V
- Dual supply
- Multimeter
Theory
Each bit switches its 2R leg to Vref (1) or ground (0). The ladder divides by 2 at each node, so the output of the inverting amplifier (Rf = R) is Vo = −Vref·(D/2ⁿ), where D is the binary input. Resolution is Vref/2ⁿ: the step for one count.
- R-2R ladder with 4 inputs (MSB nearest the op-amp); ladder end to pin 2; Rf = R from pin 2 to 6; pin 3 to ground
Procedure
Pre-lab check
4 questions · 75% to be readyTry the readings before the lab
| Code | D | Vo theory (V) |
|---|---|---|
| 0000 | 0 | 0 |
| 0001 | 1 | -0.3125 |
| 0010 | 2 | -0.625 |
| 0011 | 3 | -0.9375 |
| 0100 | 4 | -1.25 |
| 0101 | 5 | -1.5625 |
| 0110 | 6 | -1.875 |
| 0111 | 7 | -2.1875 |
| 1000 | 8 | -2.5 |
| 1001 | 9 | -2.8125 |
| 1010 | 10 | -3.125 |
| 1011 | 11 | -3.4375 |
| 1100 | 12 | -3.75 |
| 1101 | 13 | -4.0625 |
| 1110 | 14 | -4.375 |
| 1111 | 15 | -4.6875 |
Precautions
- Use 1% resistors; mismatch shows up as missing or uneven steps.
- Measure the reference voltage, do not assume it.
My readings
Type what you measured. It goes into your record book, and to My Garage when you are signed in.
| S. No. | Code | D | Vo theory (V) |
|---|---|---|---|
| 1 | |||
| 2 | |||
| 3 | |||
| 4 | |||
| 5 | |||
| 6 |
Check my readings
Put the value you set in the first column, then compare. Real parts have tolerance.
Step size = ___ mV (theory ___), maximum error = ___ mV.
Everything above is free. The print-ready write-up comes with Maker.
Printed pages leave the observation table empty for your own readings.
Viva questions
Say your answer out loud first, then check. The first 2 answers are free; Maker opens all 4.
Quick answers for your record and viva
What is the aim of the 4-bit r-2r ladder d/a converter experiment?
To build a 4-bit R-2R ladder DAC with an op-amp and measure its output for every input code, its resolution and accuracy.
What apparatus is needed for 4-bit r-2r ladder d/a converter?
IC 741, Resistors 10 kΩ and 20 kΩ (1%), Switches or an Arduino for the 4 bits, DC reference 5 V, Dual supply, Multimeter.
What is the theory behind 4-bit r-2r ladder d/a converter?
Each bit switches its 2R leg to Vref (1) or ground (0). The ladder divides by 2 at each node, so the output of the inverting amplifier (Rf = R) is Vo = −Vref·(D/2ⁿ), where D is the binary input. Resolution is Vref/2ⁿ: the step for one count.
What result should I get in 4-bit r-2r ladder d/a converter?
Step size = ___ mV (theory ___), maximum error = ___ mV.
What precautions should I take in 4-bit r-2r ladder d/a converter?
Use 1% resistors; mismatch shows up as missing or uneven steps. Measure the reference voltage, do not assume it.
