Lab / AKTU / Analog and linear ICs / Experiment 3

Op-amp integrator and differentiator

Analog and linear ICsVirtual readings4 viva questionsRecord book ready
Aim

To build an op-amp integrator and differentiator and observe their outputs for square and sine inputs.

Apparatus
  • IC 741
  • Resistors 10 kΩ, 100 kΩ, 1 kΩ
  • Capacitors 0.01 µF, 0.1 µF
  • Dual supply ±12 V
  • Function generator
  • CRO
−+Vout = −Rf/Rin · Vin

Theory

Integrator: Vo = −(1/RC)∫Vin dt, so a square input gives a triangle. A resistor Rf across C (about 10R) stops the output drifting to saturation. Differentiator: Vo = −RC·dVin/dt, so a triangle gives a square and a square gives spikes. A small series resistor at the input limits high-frequency gain. For a ±Vp square at frequency f the integrator's output swing is Vp / (2fRC) peak-to-peak.

Circuit connections
  • Integrator: input → R → pin 2; C from pin 2 to 6, with Rf in parallel; pin 3 to ground
  • Differentiator: input → C (with small series R) → pin 2; R from pin 2 to 6; pin 3 to ground

Procedure

Pre-lab check

4 questions · 75% to be ready
1Why is a resistor placed across the integrator capacitor?
2Why is a pure differentiator noisy?
3What output does an integrator give for a sine input?
4Where are integrators used?

Try the readings before the lab

Calculated, not measured. In the lab, write down your own readings.
f (Hz)Integrator out p-p, square in (V)Differentiator out peak, sine in (V)
10050.628
2002.51.257
50013.142
10000.56.283
20000.2510.5
50000.110.5

Precautions

  • Keep Rf across the integrator capacitor to avoid saturation.
  • Use a low input frequency so the output does not clip.

My readings

Type what you measured. It goes into your record book, and to My Garage when you are signed in.

S. No.f (Hz)Integrator out p-p, square in (V)Differentiator out peak, sine in (V)
1
2
3
4
5
6

Check my readings

Put the value you set in the first column, then compare. Real parts have tolerance.

Open my record book
Result

Square in gives a triangle out of ___ V p-p from the integrator (theory ___). The differentiator turns a sine into a cosine of amplitude ___ V.

Everything above is free. The print-ready write-up comes with Maker.

Printed pages leave the observation table empty for your own readings.

Viva questions

Say your answer out loud first, then check. The first 2 answers are free; Maker opens all 4.

1. Why is a resistor placed across the integrator capacitor?
2. Why is a pure differentiator noisy?
3. What output does an integrator give for a sine input?
4. Where are integrators used?

Quick answers for your record and viva

What is the aim of the op-amp integrator and differentiator experiment?

To build an op-amp integrator and differentiator and observe their outputs for square and sine inputs.

What apparatus is needed for op-amp integrator and differentiator?

IC 741, Resistors 10 kΩ, 100 kΩ, 1 kΩ, Capacitors 0.01 µF, 0.1 µF, Dual supply ±12 V, Function generator, CRO.

What is the theory behind op-amp integrator and differentiator?

Integrator: Vo = −(1/RC)∫Vin dt, so a square input gives a triangle. A resistor Rf across C (about 10R) stops the output drifting to saturation. Differentiator: Vo = −RC·dVin/dt, so a triangle gives a square and a square gives spikes. A small series resistor at the input limits high-frequency gain. For a ±Vp square at frequency f the integrator's output swing is Vp / (2fRC) peak-to-peak.

What result should I get in op-amp integrator and differentiator?

Square in gives a triangle out of ___ V p-p from the integrator (theory ___). The differentiator turns a sine into a cosine of amplitude ___ V.

What precautions should I take in op-amp integrator and differentiator?

Keep Rf across the integrator capacitor to avoid saturation. Use a low input frequency so the output does not clip.

Op-amp integrator and differentiator: lab experiment