Final-year projects / Assistive tech

Smart walking stick for the visually impaired

India has the largest number of blind people in the world, and most use a plain white cane that cannot warn of waist-high obstacles, potholes or water. A stick that senses these and buzzes or vibrates gives more independence at low cost.

Arduino NanoMini or Major projectECE, EIE, BME, Diploma
NANODOWNWATER26 cmFeatured
Parts
₹3,605
Build
11 weeks
Board
Arduino Nano
Objectives
6

Block diagram

Inputs
  • Front ultrasonic sensorFinds obstacles ahead up to 2 m
  • DOWN
    Down-facing ToF sensorFinds steps and potholes
  • WATER
    Water sensor at the tipWarns of puddles
Controller
  • NANO
    Arduino NanoDecides how urgent each warning is
Power
  • +
    18650 cellPowers the stick for days
Outputs
  • Vibration motorSilent warning in the handle
  • BuzzerAudible warning
  • 4G
    4G modemSends SMS alerts and calls over the mobile network+
  • VOICE
    Voice moduleSpeaks alerts from recorded clips+

Objectives

  1. To detect obstacles ahead from 20 cm to 2 m and warn with a vibration rate that rises as they get closer.
  2. To detect a drop of more than 10 cm in front of the tip (step or pothole).
  3. To warn of water at the tip.
  4. To test with blindfolded volunteers on a set course and compare with a plain cane.
  5. To send SMS alerts through a 4G modem where no Wi-Fi is available.
  6. To announce readings and alerts by voice in two languages.

Parts and specifications

Total about ₹3,605 at typical online prices. Tap a part for its pinout and datasheet notes.

Design calculations

Warning rate

Pulse period = 100 ms + distance(cm) × 5 ms. At 150 cm the motor pulses every 850 ms; at 30 cm every 250 ms, so closer feels more urgent.

Drop detection

The ToF sensor points down and forward and reads about 80 cm to the ground when held normally. A reading above 95 cm means a step or pothole of more than 15 cm.

Transistor base resistor

Motor 70 mA, BC547 hFE about 100: base current needs 0.7 mA × 3 for saturation ≈ 2 mA. Rb = (5 − 0.7) / 2 mA ≈ 2.2 kΩ.

Battery life

Average 60 mA (sensors 20 mA, Nano 20 mA, motor 25% duty). 2600 × 0.8 / 60 ≈ 35 hours, several days of walking.

Pin map

SignalPin or connection
HC-SR04 TRIG / ECHOD9 / D10
VL53L0X SDA / SCLA4 / A5 (I²C 0x29)
Water sensorA0, powered from D7 only while reading
Vibration motor (BC547 + diode)D5 (PWM)
BuzzerD6
Power18650 → TP4056 → MT3608 5 V → Nano 5V pin

Firmware outline

  1. Every 60 ms read the front distance (median of 3) and the down distance.
  2. If the down distance jumps by more than 15 cm, give a long buzz: drop ahead.
  3. If front distance < 200 cm, pulse the vibration motor with the distance-based period.
  4. Every 2 s power the water sensor, read it, and give a double beep if wet.
  5. Sleep the sensors when the stick is held still for 5 minutes.

Test plan

TestExpected result
Wall at 50, 100, 150 cmPulse rate rises as it gets closer
Step down of 15 cmDrop warning before the tip goes over
Tip in a puddleDouble beep
Blindfolded course with 6 obstaclesCollisions counted with and without the stick

These rows start your results table when you plan the project.

Viva practice

Say your answer out loud first, then check. The first 2 answers are free; Maker opens all 5.

1. Why add a ToF sensor when you have ultrasound?
2. Why vibration and not only sound?
3. What is the ultrasonic blind spot?
4. How did you decide the warning distances?
5. How would you help navigation, not just obstacles?

Make it yours

One or two upgrades for a mini project, two to four for a major one.

Build these first

Datasheets and sources to cite

  • HC-SR04 user guide
  • STMicroelectronics VL53L0X datasheet
  • WHO World Report on Vision (2019)

About this project

How much does the smart walking stick for the visually impaired project cost?

About ₹1,655 for the parts in the base list: Arduino Nano (CH340, Type-C), HC-SR04 ultrasonic sensor, VL53L0X time-of-flight sensor, Water level sensor (strip), Coin vibration motor, Active buzzer 5 V, 18650 cell 2600 mAh (branded), TP4056 charger with protection, MT3608 boost converter, Folding stick, BC547, diode and case.

How long does it take?

About 8 weeks for the base project, built on an Arduino Nano. Each upgrade adds time.

Which branches is it suitable for?

Electronics and Communication, Instrumentation, Biomedical, Diploma (any electronics branch), as a mini or major project.

Which pins and design calculations does it use?

HC-SR04 TRIG / ECHO on D9 / D10; VL53L0X SDA / SCL on A4 / A5 (I²C 0x29); Water sensor on A0, powered from D7 only while reading. Worked calculations on this page: warning rate, drop detection, transistor base resistor, battery life.

How do I test it?

Wall at 50, 100, 150 cm: Pulse rate rises as it gets closer. Step down of 15 cm: Drop warning before the tip goes over. Tip in a puddle: Double beep. Blindfolded course with 6 obstacles: Collisions counted with and without the stick.

What are the objectives?

To detect obstacles ahead from 20 cm to 2 m and warn with a vibration rate that rises as they get closer. To detect a drop of more than 10 cm in front of the tip (step or pothole). To warn of water at the tip. To test with blindfolded volunteers on a set course and compare with a plain cane.