Projects / Reverse parking sensor

Reverse parking sensor

Beginner2.5 hGuided buildReviewed

Build it step by step

0 of 6 done
  1. NANOLM2596

    Set the regulator

    Before connecting the Nano, power the LM2596 from a 12 V source and turn it to exactly 5.0 V.

  2. NANO

    Wire the power

    Take the feed from the reverse light wire through a 3 A in-line fuse. Never power it from the Nano's USB.

  3. NANO

    Wire the sensor

    TRIG to D2, ECHO to D3, VCC to 5V, GND to GND. Run the sensor on its cable through the bumper.

  4. NANO18.9 mA

    Add the alerts

    Buzzer to D5, red LED to D6 and green to D7, each LED with 220 Ω.

  5. NANO

    Upload and test on the bench

    Hold a book at different distances and check the beeps.

  6. NANO

    Mount

    Seal all joints with silicone and heat-shrink, mount the sensor facing back at about 50 cm height, and test slowly with a helper.

In short

How do you build a reverse parking sensor?

A waterproof ultrasonic sensor on the bumper beeps faster as you get closer when reversing, with a steady tone under 30 cm. You need Arduino Nano, JSN-SR04T waterproof ultrasonic sensor, Active buzzer 5 V, LED 5 mm red, LED 5 mm green, Resistor 220 Ω × 2, LM2596 Buck Module, Blade fuse with inline holder (car type) and ABS project box (100 × 60 × 25 mm). It takes 6 steps and about 150 minutes.

Level
Beginner
Time
About 150 min
Parts
9

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Reverse light + (through the in-line fuse)LM2596 IN+Power only while reversing
Vehicle groundLM2596 IN−Return
LM2596 OUT+ / OUT− (set to 5.0 V first)Nano 5V / GNDRegulated power
JSN-SR04T TRIG / ECHONano D2 / D3Distance
JSN-SR04T VCC / GNDNano 5V / GNDSensor power
Active buzzer + / −Nano D5 / GNDBeeps
Green LED anode through 220 ΩNano D7, cathode to GNDClear
Red LED anode through 220 ΩNano D6, cathode to GNDClose

Code

Arduino IDE, board "Arduino Nano" (processor ATmega328P, or ATmega328P (Old Bootloader) for clones). No libraries. The JSN-SR04T cannot measure closer than about 20 cm, which is why the steady tone starts at 30 cm.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

const byte TRIG = 2, ECHO = 3, BUZ = 5, RED = 6, GREEN = 7;

float readCm() {
  float v[3];
  for (byte i = 0; i < 3; i++) {                    // take three readings and use the middle one
    digitalWrite(TRIG, LOW); delayMicroseconds(4);
    digitalWrite(TRIG, HIGH); delayMicroseconds(12);
    digitalWrite(TRIG, LOW);
    long us = pulseIn(ECHO, HIGH, 30000);           // 30 ms timeout is about 5 m
    v[i] = us ? us / 58.0 : 999;
    delay(15);
  }
  if (v[0] > v[1]) { float t = v[0]; v[0] = v[1]; v[1] = t; }
  if (v[1] > v[2]) { float t = v[1]; v[1] = v[2]; v[2] = t; }
  if (v[0] > v[1]) { float t = v[0]; v[0] = v[1]; v[1] = t; }
  return v[1];
}

void setup() {
  pinMode(TRIG, OUTPUT); pinMode(ECHO, INPUT);
  pinMode(BUZ, OUTPUT); pinMode(RED, OUTPUT); pinMode(GREEN, OUTPUT);
}

void loop() {
  float cm = readCm();
  digitalWrite(GREEN, cm > 150); digitalWrite(RED, cm <= 150);
  if (cm > 150) { digitalWrite(BUZ, LOW); delay(100); return; }       // clear: silent
  if (cm < 30) { digitalWrite(BUZ, HIGH); delay(100); return; }       // too close: steady tone
  unsigned int gap = map((long)cm, 30, 150, 80, 600);                 // closer means faster beeps
  digitalWrite(BUZ, HIGH); delay(60);
  digitalWrite(BUZ, LOW); delay(gap);
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Object at 2 mGreen LED, silent
Object at 1 mRed LED, a beep about every 350 ms
Object at 40 cmBeeps about every 140 ms
Object at 20 cmSteady tone

If it does not work

Random beeps with nothing behind

The sensor may be catching the bumper or the tow bar. Aim it slightly down and away.

Readings are zero

Check TRIG and ECHO are not swapped and the sensor has 5 V.

The Nano resets when the engine starts

Supply noise. Add a 470 µF capacitor on the LM2596 output.

It does not work in heavy rain

Water on the face of the sensor can cause false readings. Dry it or wipe it.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the reverse parking sensor?

Arduino Nano, JSN-SR04T waterproof ultrasonic sensor, Active buzzer 5 V, LED 5 mm red, LED 5 mm green, Resistor 220 Ω × 2, LM2596 Buck Module, Blade fuse with inline holder (car type) and ABS project box (100 × 60 × 25 mm).

How long does the reverse parking sensor take to build?

About 150 minutes for a beginner maker, in 6 steps.

How do I know the reverse parking sensor works?

Object at 2 m: Green LED, silent. Object at 1 m: Red LED, a beep about every 350 ms. Object at 40 cm: Beeps about every 140 ms.

Random beeps with nothing behind: what should I check?

The sensor may be catching the bumper or the tow bar. Aim it slightly down and away.

Readings are zero: what should I check?

Check TRIG and ECHO are not swapped and the sensor has 5 V.

The Nano resets when the engine starts: what should I check?

Supply noise. Add a 470 µF capacitor on the LM2596 output.

It does not work in heavy rain: what should I check?

Water on the face of the sensor can cause false readings. Dry it or wipe it.