Underground cable fault distance locator
Cities are moving power lines underground, but finding a fault in a buried cable means digging up long stretches. Measuring the resistance to the fault from one end tells the crew how many metres away to dig.
- Parts
- ₹3,204
- Build
- 12 weeks
- Board
- Arduino Uno
- Objectives
- 6
Block diagram
- Resistor cable modelEach 1 kΩ stands for 1 km of cable
- Fault switchesCreate short and open faults
- Arduino UnoMeasures voltage and works out distance
- RelaysSelect each phase in turn
- LCDShows phase and distance
- 4G modemSends SMS alerts and calls over the mobile network+
- Cloud dashboardStores readings, plots trends and sends alerts+
Objectives
- To model a three-phase cable 4 km long with resistors and switchable faults.
- To find which phase has the fault and its distance in km from the measured voltage.
- To tell a short-circuit fault from an open-circuit fault.
- To measure the distance error for every fault position.
- To send SMS alerts through a 4G modem where no Wi-Fi is available.
- To publish readings over MQTT and show them on a live dashboard with threshold alerts.
Parts and specifications
- Arduino Uno R3 (CH340 clone)ATmega328P 16 MHz, 32 KB flash, 2 KB SRAM, 5 V logic, 6 analog inputs (10-bit), 6 PWM pins₹450Buy
- 5 V relay module (4 channel)Four 10 A 250 V AC relays, opto inputs, separate JD-VCC for coil supply₹220Buy
- 16×2 LCD with I²C backpackHD44780, PCF8574 at 0x27 or 0x3F, 5 V, contrast trimmer on the back₹220Buy
- × 121 kΩ 1% resistors (cable model, 3 phases × 4 km)₹24
- × 12Fault toggle switches₹180
- ADS1115 16-bit ADC (better resolution)Four channels, 16-bit, programmable gain ±0.256 to ±6.144 V, I²C 0x48₹250Buy
- 5 V 2 A adapter₹150
- A7670C 4G LTE module4G Cat-1 with 2G fallback, SMS, calls and data, works with any Indian SIM including Jio; 3.4 to 4.2 V, 2 A peaks₹1,500Buy
- LM2596 buck converter (set to 4.0 V for the modem)4 to 40 V in, 1.25 to 37 V out, up to 2 A continuous (3 A peak), about 85% efficient₹90Buy
Total about ₹3,204 at typical online prices. Tap a part for its pinout and datasheet notes.
Design calculations
The series resistor Rs and the cable to the fault form a divider: V = 5 × Rf / (Rs + Rf), so Rf = Rs × V / (5 − V).
Each 1 kΩ in the model is 1 km. A short at 3 km gives Rf = 3 kΩ: V = 5 × 3 / 4 = 3.75 V, and back Rf = 1 × 3.75 / 1.25 = 3 kΩ = 3 km.
Between 3 km (3.75 V) and 4 km (4.0 V) the step is 250 mV. A 10-bit ADC step is 4.9 mV and the ADS1115 0.19 mV, so both resolve 1 km easily; finer steps need the 16-bit ADC.
A real 95 mm² aluminium core is about 0.32 Ω per km, so field locators use a bridge (Murray loop) or time-domain reflectometry, not a simple divider.
Pin map
| Signal | Pin or connection |
|---|---|
| ADS1115 SDA / SCL | A4 / A5 (or A0 direct for the basic version) |
| Phase R / Y / B select relays | D2 / D3 / D4 |
| LCD SDA / SCL | A4 / A5 (shared I²C) |
| Measuring series resistor | 1 kΩ 1% from 5 V to the selected phase |
Firmware outline
- Select phase R with its relay, wait 50 ms, read the voltage (average 16 samples).
- If V is near 5 V, no fault on this phase (open line or healthy).
- Else compute Rf and the distance, rounded to the nearest km.
- Repeat for Y and B; show 'R: 2 km Y: ok B: 4 km' on the LCD.
- Report an open fault when the far-end loop resistance is missing.
Test plan
| Test | Expected result |
|---|---|
| Short at each of 1 to 4 km on each phase | Correct phase and distance |
| No fault | All phases ok |
| Two faults on different phases | Both found |
| Resistor tolerance 5% vs 1% | Distance error compared |
These rows start your results table when you plan the project.
Viva practice
Say your answer out loud first, then check. The first 2 answers are free; Maker opens all 5.
Make it yours
One or two upgrades for a mini project, two to four for a major one.
Build these first
Datasheets and sources to cite
- Murray and Varley loop test (IEEE Std 400 guide on cable fault location)
- Microchip ATmega328P datasheet
- TI ADS1115 datasheet
About this project
How much does the underground cable fault distance locator project cost?
About ₹1,614 for the parts in the base list: Arduino Uno R3 (CH340 clone), 5 V relay module (4 channel), 16×2 LCD with I²C backpack, 1 kΩ 1% resistors (cable model, 3 phases × 4 km) × 12, Fault toggle switches × 12, Zero PCB 10 × 15 cm × 2, ADS1115 16-bit ADC (better resolution), 5 V 2 A adapter.
How long does it take?
About 8 weeks for the base project, built on an Arduino Uno. Each upgrade adds time.
Which branches is it suitable for?
Electrical and Electronics, Electronics and Communication, Diploma (any electronics branch), as a mini or major project.
Which pins and design calculations does it use?
ADS1115 SDA / SCL on A4 / A5 (or A0 direct for the basic version); Phase R / Y / B select relays on D2 / D3 / D4; LCD SDA / SCL on A4 / A5 (shared I²C). Worked calculations on this page: voltage to resistance, resistance to distance, resolution, real cables.
How do I test it?
Short at each of 1 to 4 km on each phase: Correct phase and distance. No fault: All phases ok. Two faults on different phases: Both found. Resistor tolerance 5% vs 1%: Distance error compared.
What are the objectives?
To model a three-phase cable 4 km long with resistors and switchable faults. To find which phase has the fault and its distance in km from the measured voltage. To tell a short-circuit fault from an open-circuit fault. To measure the distance error for every fault position.
