Projects / Relay module lab at 12 V

Relay module lab at 12 V

Beginner30 minGuided buildReviewed

Build it step by step

0 of 7 done
  1. UNO

    Wire the control side

    Connect VCC, GND and IN to the Uno.

  2. UNOON

    Upload the sketch

    Listen for the relay click every two seconds.

  3. UNO1212.7 mA

    Check the contacts

    With the 12 V adapter unplugged, wire COM and NO through the strip.

  4. UNO1212.7 mA

    Plug in the adapter

    The strip should switch on and off with the click.

  5. UNO

    Flip the logic

    If it works backwards, change ACTIVE_LOW.

  6. UNO

    Look at the module

    Find the flyback diode and the optocoupler on the board.

  7. UNOON12.8 mA

    Try the other contact

    Use NC (normally closed) and see the strip on when the relay is off.

In short

How do you build a relay module lab at 12 V?

Switch a 12 V lamp with a relay module from an Arduino and see why a flyback diode and opto-isolation matter. You need Arduino Uno R3, Relay Module 5V, 12 V LED strip warm white (5 m, 2835), 12 V 2 A DC adapter, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 7 steps and about 30 minutes.

Level
Beginner
Time
About 30 min
Parts
6

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Relay module VCCUno 5VCoil power
Relay module GNDUno GNDGround
Relay module INUno D7Control signal
12 V adapter +Relay COMSupply into the relay contact
Relay NO (normally open)LED strip +Strip is powered when the relay closes
LED strip -12 V adapter -Return path
UnoUSB cable to the computerPower for the Uno, separate from the 12 V adapter

Code

Only low voltage is used: a 12 V DC adapter and a 12 V LED strip. Never use mains in this lab, and never connect a mains load to a relay module on a classroom bench; mains wiring belongs to a qualified electrician. The relay coil is an inductor and makes a voltage spike when it switches off, which is why the module has a flyback diode across the coil and a transistor and optocoupler between your Arduino and the coil. Many modules turn on when the input is pulled low, so the code has a flag. Keep the 12 V wires short and tidy and check polarity before connecting the adapter. Arduino IDE, board "Arduino Uno" (or "Arduino Nano" with processor ATmega328P).

Runs on a virtual Arduino Uno in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// Relay module control. Most blue relay boards are active-low: LOW turns the relay on.
const byte RELAY = 7;
const bool ACTIVE_LOW = true;   // set false if your module turns on with HIGH

void relay(bool on) {
  digitalWrite(RELAY, (on == ACTIVE_LOW) ? LOW : HIGH);
}

void setup() {
  pinMode(RELAY, OUTPUT);
  relay(false);                 // start off
  Serial.begin(9600);
}

void loop() {
  relay(true);
  Serial.println("relay on");
  delay(2000);
  relay(false);
  Serial.println("relay off");
  delay(2000);
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual Arduino Uno with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

relay on
relay off
relay on
relay off

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Sketch runningClick every two seconds
12 V strip on NOOn when the relay clicks on
Strip on NCOn when the relay is off
Active level wrongStrip switches opposite to the serial text

If it does not work

No click

Check the 5 V and GND to the relay board.

Clicks but no light

Check the COM and NO wiring and the adapter.

Uno resets when it clicks

Power the Uno separately from USB and keep wires apart.

Strip stays on

Check you used NO and not NC.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the relay module lab at 12 V?

Arduino Uno R3, Relay Module 5V, 12 V LED strip warm white (5 m, 2835), 12 V 2 A DC adapter, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).

How long does the relay module lab at 12 V take to build?

About 30 minutes for a beginner maker, in 7 steps.

How do I know the relay module lab at 12 V works?

Sketch running: Click every two seconds. 12 V strip on NO: On when the relay clicks on. Strip on NC: On when the relay is off.

No click: what should I check?

Check the 5 V and GND to the relay board.

Clicks but no light: what should I check?

Check the COM and NO wiring and the adapter.

Uno resets when it clicks: what should I check?

Power the Uno separately from USB and keep wires apart.

Strip stays on: what should I check?

Check you used NO and not NC.