Projects / Voltage divider explorer

Voltage divider explorer

Beginner30 minGuided buildReviewed

Build it step by step

0 of 6 done
  1. Predict

    For 9 V with two 10 kΩ resistors, write down the output you expect.

  2. Build the divider

    Two 10 kΩ in series from 9 V to ground.

  3. Measure

    Put the meter black probe on ground and red on the middle. It should read near 4.5 V.

  4. Use the pot

    Replace the fixed pair with the pot's outer pins on 9 V and ground and measure the wiper while turning it.

  5. Load it

    Go back to the fixed divider and add 1 kΩ across the bottom resistor.

  6. Compare

    The output drops to under 1 V. Work out the loaded value with the formula.

In short

How do you build a voltage divider explorer?

Build dividers with fixed resistors and a pot, then see how loading changes the output. You need Digital multimeter, Resistor 10 kΩ × 2, Resistor 1 kΩ × 2, Potentiometer 10 kΩ, Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm), 9 V battery and 9 V battery snap with DC jack. It takes 6 steps and about 30 minutes.

Level
Beginner
Time
About 30 min
Parts
8
See the electronics first. This build uses voltage divider. Try a voltage divider in the circuit builder and watch the voltages and currents before you wire it.

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
9 V battery +Top of R1 (10 kΩ)Supply
R1 bottom and R2 topOutput node (measure here)Divider middle
R2 bottom (10 kΩ)Battery -Ground
Load resistor (1 kΩ)Output node to groundAdded later to see loading
Pot outer pinsBattery + and battery -Replace the fixed divider
Pot middle pinDMM red probeVariable output

No code needed

No code. The formula is Vout = Vin × R2 / (R1 + R2). A load resistor in parallel with R2 lowers its effective value: 10 kΩ in parallel with 1 kΩ is about 0.91 kΩ.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Two equal resistorsOutput about half the supply
Pot at the extremesOutput near 0 V and near 9 V
1 kΩ load on a 10 kΩ and 10 kΩ dividerOutput about 0.75 V
Divider with 1 kΩ and 1 kΩ and a 10 kΩ loadOutput barely changes

If it does not work

Output is zero

The ground connection is missing or the probes are in the wrong sockets.

Output is the full 9 V

R2 is not connected to ground.

Readings differ from calculation

Resistors are 5 % off and the battery sags. Measure the actual values.

Pot gives odd readings

Check you used the middle pin as the output and outer pins as the supply.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the voltage divider explorer?

Digital multimeter, Resistor 10 kΩ × 2, Resistor 1 kΩ × 2, Potentiometer 10 kΩ, Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm), 9 V battery and 9 V battery snap with DC jack.

How long does the voltage divider explorer take to build?

About 30 minutes for a beginner maker, in 6 steps.

How do I know the voltage divider explorer works?

Two equal resistors: Output about half the supply. Pot at the extremes: Output near 0 V and near 9 V. 1 kΩ load on a 10 kΩ and 10 kΩ divider: Output about 0.75 V.

Output is zero: what should I check?

The ground connection is missing or the probes are in the wrong sockets.

Output is the full 9 V: what should I check?

R2 is not connected to ground.

Readings differ from calculation: what should I check?

Resistors are 5 % off and the battery sags. Measure the actual values.

Pot gives odd readings: what should I check?

Check you used the middle pin as the output and outer pins as the supply.