Projects / Ohm's law lab with a multimeter

Ohm's law lab with a multimeter

Beginner45 minGuided buildReviewed

Build it step by step

0 of 6 done
  1. ++

    Measure the battery

    Set the meter to DC volts and note the voltage of the 2 AA cells.

  2. Measure each resistor

    Use the ohm range, note the real values (they are 5 % off).

  3. Measure current

    Put the meter on the mA range in series with the battery and one resistor.

  4. Measure voltage

    Switch to volts across that resistor.

  5. Repeat

    Do this for all three resistors and tabulate V, I and R.

  6. Plot

    Draw V against I. The slope is the resistance. Does it match the value you measured?

In short

How do you build an ohm's law lab with a multimeter?

Measure voltage and current through different resistors and plot them to see Ohm's law for yourself. You need Digital multimeter, Resistor 220 Ω, Resistor 1 kΩ, Resistor 10 kΩ, Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm), Battery holder 2 × AA and AA alkaline battery × 2. It takes 6 steps and about 45 minutes.

Level
Beginner
Time
About 45 min
Parts
8
See the electronics first. This build uses LED with a resistor. Try an LED with a resistor in the circuit builder and watch the voltages and currents before you wire it.

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Battery pack +Resistor under test, then the meter's mA input (red probe)Current measured in series
Resistor other endBattery pack -Completes the loop
Meter set to DC mA, black probeCOM, then the circuitAmmeter is in series
Voltage checkMeter in volts across the resistorParallel connection

No code needed

No code. With two AA cells (about 3 V) expect about 14 mA through 220 Ω, 3 mA through 1 kΩ and 0.3 mA through 10 kΩ. Never connect the meter's current range across the battery or a power source directly, because that blows its fuse.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
220 ΩAbout 13 to 14 mA
1 kΩAbout 3 mA
10 kΩAbout 0.3 mA
Slope of V against IMatches the measured resistance within 5 to 10 %

If it does not work

Meter reads zero current

The meter's red probe is in the wrong socket or the fuse is blown.

Current is much lower than predicted

Batteries are weak or the meter's own burden voltage matters on the 200 µA range. Use the 20 mA range.

Voltage reading is lower than the battery's

The batteries sag under load. Note it.

Resistor warms up

Not with these values. Check you did not use the wrong resistor or voltage.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the ohm's law lab with a multimeter?

Digital multimeter, Resistor 220 Ω, Resistor 1 kΩ, Resistor 10 kΩ, Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm), Battery holder 2 × AA and AA alkaline battery × 2.

How long does the ohm's law lab with a multimeter take to build?

About 45 minutes for a beginner maker, in 6 steps.

How do I know the ohm's law lab with a multimeter works?

220 Ω: About 13 to 14 mA. 1 kΩ: About 3 mA. 10 kΩ: About 0.3 mA.

Meter reads zero current: what should I check?

The meter's red probe is in the wrong socket or the fuse is blown.

Current is much lower than predicted: what should I check?

Batteries are weak or the meter's own burden voltage matters on the 200 µA range. Use the 20 mA range.

Voltage reading is lower than the battery's: what should I check?

The batteries sag under load. Note it.

Resistor warms up: what should I check?

Not with these values. Check you did not use the wrong resistor or voltage.