Projects / Precision voltage divider with a trimmer

Precision voltage divider with a trimmer

Beginner45 minGuided buildReviewed

Build it step by step

0 of 8 done
  1. Measure the supply

    Read the exact voltage of your 5 V source.

  2. Wire the divider

    5 V, 1 kilohm, trimmer, 4.7 kilohm, GND.

  3. Connect the meter

    Red to the wiper, black to GND.

  4. Find the range

    Turn the trimmer to each end and note the voltages.

  5. Set a target

    Turn the screw slowly until the meter shows 2.50 V.

  6. Add a load

    Put the 4.7 kilohm resistor from the wiper to GND.

  7. Note the drop

    Compare with the calculated 1.36 V.

  8. Repeat with 1 kilohm

    The output falls much further.

In short

How do you build a precision voltage divider with a trimmer?

A multi-turn trimmer sets an exact voltage from a supply, then you load it and see how the output sags. You need Trimmer potentiometer 10 kΩ (3296), Resistor 1 kΩ, Resistor 4.7 kΩ, 5 V 2 A USB adapter, Digital multimeter, Jumper wires male to male (40 pcs, 20 cm) and Breadboard 830 Tie Points. It takes 8 steps and about 45 minutes.

Level
Beginner
Time
About 45 min
Parts
7
See the electronics first. This build uses voltage divider. Try a voltage divider in the circuit builder and watch the voltages and currents before you wire it.

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
5 V supply positive1 kilohm resistorTop of the divider
1 kilohm resistorTrimmer end pin 1Upper part of the divider
Trimmer end pin 34.7 kilohm resistorLower part of the divider
4.7 kilohm resistorSupply negative (GND)Ground
Trimmer middle pin (wiper)Multimeter red probeThe adjustable output
Multimeter black probeSupply negative (GND)Common ground

Code

A voltage divider is two resistances in series, and the voltage at the join is the supply times the lower part divided by the total. A multi-turn trimmer, which takes about 25 turns to go from end to end, lets you move that join in very small steps. Here the 1 kilohm and 4.7 kilohm resistors on each end narrow the range to roughly 1.5 to 4.7 volts, which makes each turn of the screw change the output by only a small amount, so setting exactly 2.500 volts is easy. First measure your real supply, because a USB adapter may be anywhere from 4.8 to 5.2 volts, and expect the output to scale with it. Then turn the screw until the meter reads your target. The most useful part comes next. Connect the 4.7 kilohm resistor across the output as a load, and the voltage drops to about 1.4 volts, because the divider has a high output resistance of nearly 4 kilohms. This is why a divider can set a reference or a threshold for a high impedance input, but cannot power anything, and why designers add a buffer such as an op-amp when they need the voltage to hold under load. A multimeter has a very high input resistance, so it hardly disturbs the reading, which you can check by comparing it with the calculated value.

Build notes (no code needed for this build)

Divider: 5 V -> 1k -> [10k trimmer, wiper is the output] -> 4.7k -> GND.
Total resistance 1k + 10k + 4.7k = 15.7k.

Output range with no load:
  wiper at the GND end : 5 x 4.7 / 15.7 = about 1.50 V
  wiper at the 5 V end : 5 x 14.7 / 15.7 = about 4.68 V

For exactly 2.5 V: the part below the wiper plus 4.7k must be 7.85k,
so the wiper sits about 3.15k from the GND end of the trimmer.

Output resistance at 2.5 V (calculated): about 3.9k.
With a 4.7k load the output falls to about 1.36 V.
With a 1k load the output falls to about 0.5 V.
(The real numbers move a little with resistor tolerance and the supply voltage.)

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
No load, wiper at one endAbout 1.5 V
No load, wiper at the other endAbout 4.7 V
Wiper adjusted2.50 V within a few millivolts
4.7 kilohm loadOutput near 1.4 V
1 kilohm loadOutput near 0.5 V

If it does not work

Output does not change

Check you are on the middle pin.

Output stuck at an end

Check both end pins are connected through the resistors.

Reading jumps

Loose breadboard contact, press the trimmer in.

Numbers differ from the calculation

Measure the supply and the real resistor values.

Clicking while turning

The trimmer has reached the end of its travel.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the precision voltage divider with a trimmer?

Trimmer potentiometer 10 kΩ (3296), Resistor 1 kΩ, Resistor 4.7 kΩ, 5 V 2 A USB adapter, Digital multimeter, Jumper wires male to male (40 pcs, 20 cm) and Breadboard 830 Tie Points.

How long does the precision voltage divider with a trimmer take to build?

About 45 minutes for a beginner maker, in 8 steps.

How do I know the precision voltage divider with a trimmer works?

No load, wiper at one end: About 1.5 V. No load, wiper at the other end: About 4.7 V. Wiper adjusted: 2.50 V within a few millivolts.

Output does not change: what should I check?

Check you are on the middle pin.

Output stuck at an end: what should I check?

Check both end pins are connected through the resistors.

Reading jumps: what should I check?

Loose breadboard contact, press the trimmer in.

Numbers differ from the calculation: what should I check?

Measure the supply and the real resistor values.