Projects / State machine vending model

State machine vending model

Intermediate1.5 hGuided buildReviewed

Build it step by step

0 of 8 done
  1. UNO

    Draw the states

    Sketch IDLE, CREDIT, DISPENSE and CHANGE with arrows for each button.

  2. UNO

    Wire the buttons and display

    Connect as in the table.

  3. UNO

    Test the coin

    Each press adds 5 to the credit shown.

  4. UNO

    Buy item A

    Press coin twice and then item A.

  5. UNO

    Test not enough credit

    Press item B with only 10 and hear the beeps.

  6. UNO

    Test change

    Add 20 and buy item A, then count the change beeps.

  7. UNO

    Test cancel

    Insert coins and press cancel to get the refund.

  8. UNO

    Extend it

    Add a third item or a sold-out state.

In short

How do you build a state machine vending model?

A coin button, item buttons and a servo dispenser model a vending machine with states. You need Arduino Uno R3, Tactile push button 6 mm × 4, SG90 Micro Servo, 16x2 LCD with I2C backpack (PCF8574), Passive buzzer, Electrolytic Capacitor 100 µF, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 8 steps and about 90 minutes.

Level
Intermediate
Time
About 90 min
Parts
8

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Coin buttonUno D2 and GNDAdds 5 to the credit
Item A buttonUno D3 and GNDPrice 10
Item B buttonUno D4 and GNDPrice 15
Cancel buttonUno D5 and GNDRefund
Passive buzzer +Uno D6Beeps
Passive buzzer -Uno GNDGround
Servo signalUno D9Dispenser arm
Servo red and brownUno 5V and GNDPower, with the 100 µF capacitor across them
LCD I2C SDA and SCLUno A4 and A5Display
LCD I2C VCC and GNDUno 5V and GNDPower

Code

A state machine keeps one clear current state and decides what each input does in that state, which avoids tangled if statements. The four states here are idle (no money), credit (money inserted), dispense (servo arm moving) and change (give money back). The model uses a servo arm as the dispenser and one beep for each 5 unit coin of change, so no real money or mechanism is involved. A small servo can run from the Uno 5 V pin for this light load with a 100 µF capacitor across the supply. Draw the state diagram on paper first and compare it with the code. Arduino IDE, board "Arduino Uno" (or "Arduino Nano" with processor ATmega328P).

Runs on a virtual Arduino Uno in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// States: IDLE, CREDIT, DISPENSE, CHANGE. Libraries: Servo, LiquidCrystal_I2C.
#include <Servo.h>
#include <Wire.h>
#include <LiquidCrystal_I2C.h>

enum State { IDLE, CREDIT, DISPENSE, GIVE_CHANGE };
State state = IDLE;

const byte COIN = 2, ITEM_A = 3, ITEM_B = 4, CANCEL = 5, BUZ = 6;
const int PRICE_A = 10, PRICE_B = 15, COIN_VALUE = 5;
int credit = 0, price = 0;
unsigned long stateStart = 0;
Servo arm;
LiquidCrystal_I2C lcd(0x27, 16, 2);

bool pressed(byte pin) {                       // returns true once per press, with debounce
  static unsigned long last[8];
  if (digitalRead(pin) == LOW && millis() - last[pin] > 250) { last[pin] = millis(); return true; }
  return false;
}

void show(const char *a, const char *b = "") {
  lcd.clear(); lcd.setCursor(0, 0); lcd.print(a); lcd.setCursor(0, 1); lcd.print(b);
}

void beeps(int n) { for (int i = 0; i < n; i++) { tone(BUZ, 1500, 80); delay(160); } }

void go(State s) { state = s; stateStart = millis(); }

void setup() {
  for (byte p = 2; p <= 5; p++) pinMode(p, INPUT_PULLUP);
  arm.attach(9); arm.write(0);
  lcd.init(); lcd.backlight();
  show("Insert coin", "A=10  B=15");
}

void loop() {
  switch (state) {
    case IDLE:
      if (pressed(COIN)) { credit += COIN_VALUE; go(CREDIT); char b[17]; sprintf(b, "Credit %d", credit); show(b, "A=10  B=15"); }
      break;
    case CREDIT:
      if (pressed(COIN)) { credit += COIN_VALUE; char b[17]; sprintf(b, "Credit %d", credit); show(b, "A=10  B=15"); }
      if (pressed(ITEM_A) || pressed(ITEM_B)) {
        price = digitalRead(ITEM_A) == LOW ? PRICE_A : PRICE_B;
        if (credit >= price) { credit -= price; show("Dispensing...", ""); arm.write(90); go(DISPENSE); }
        else { show("Need more coins", ""); beeps(2); }
      }
      if (pressed(CANCEL)) { go(GIVE_CHANGE); show("Refund", ""); }
      break;
    case DISPENSE:
      if (millis() - stateStart > 1000) { arm.write(0); go(GIVE_CHANGE); show("Enjoy! Change:", ""); }
      break;
    case GIVE_CHANGE: {
      int coins = credit / COIN_VALUE;
      beeps(coins);                              // one beep for each coin of change
      credit = 0;
      delay(500);
      go(IDLE);
      show("Insert coin", "A=10  B=15");
      break;
    }
  }
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Coin pressedCredit rises by 5
Item A with 10 or moreServo moves and credit falls by 10
Not enough creditMessage and two beeps
CancelOne beep per coin of refund

If it does not work

Presses repeat

Increase the debounce time.

Servo jitters

Add the capacitor or power it separately.

LCD blank

Try address 0x3F and adjust the contrast.

Wrong item bought

Check D3 and D4 wiring.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the state machine vending model?

Arduino Uno R3, Tactile push button 6 mm × 4, SG90 Micro Servo, 16x2 LCD with I2C backpack (PCF8574), Passive buzzer, Electrolytic Capacitor 100 µF, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).

How long does the state machine vending model take to build?

About 90 minutes for a intermediate maker, in 8 steps.

How do I know the state machine vending model works?

Coin pressed: Credit rises by 5. Item A with 10 or more: Servo moves and credit falls by 10. Not enough credit: Message and two beeps.

Presses repeat: what should I check?

Increase the debounce time.

Servo jitters: what should I check?

Add the capacitor or power it separately.

LCD blank: what should I check?

Try address 0x3F and adjust the contrast.

Wrong item bought: what should I check?

Check D3 and D4 wiring.