Projects / Electronic dice

Electronic dice

Beginner1 hGuided buildReviewed

Build it step by step

0 of 8 done
  1. UNO12:45

    Find the display pins

    Check the datasheet: two common pins in the middle of the top and bottom rows.

  2. UNO12:45

    Wire the common pin

    Both common pins to GND.

  3. UNO12:45

    Wire each segment

    a to g on D2 to D8, each through 330 ohm.

  4. UNO

    Wire the button

    D9 to GND.

  5. UNO

    Upload the sketch

    The display shows a 6.

  6. UNO12:45

    Press and hold the button

    The segments spin round.

  7. UNO

    Release

    A number from 1 to 6 shows.

  8. UNO

    Roll twenty times

    Check that all six numbers come up.

In short

How do you build an electronic dice?

A button rolls a random number from one to six on a single seven segment display, with a short spin animation. You need Arduino Uno R3, 7-segment display 1 digit (common cathode), Resistor 330 Ω × 7, Tactile push button 6 mm, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 8 steps and about 60 minutes.

Level
Beginner
Time
About 60 min
Parts
6

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Segment aUno D2 through 330 ohmTop bar
Segment bUno D3 through 330 ohmTop right
Segment cUno D4 through 330 ohmBottom right
Segment dUno D5 through 330 ohmBottom bar
Segment eUno D6 through 330 ohmBottom left
Segment fUno D7 through 330 ohmTop left
Segment gUno D8 through 330 ohmMiddle bar
Common cathode pinUno GNDBoth common pins of the display
Roll buttonUno D9 to GNDInternal pull-up, pressed reads LOW

Code

A seven-segment digit is seven LEDs labelled a to g that share one pin, the common cathode, which goes to ground. To light a segment you put its pin HIGH through a resistor. Each digit is stored as a pattern of seven bits, so the number 2, which lights a, b, d, e and g, is 0101 1011 in binary, or 0x5B. The show() function writes each bit to its pin. Without resistors the LEDs and the Uno pins would be overloaded, so every segment has its own 330 ohm resistor, giving about 7 milliamps per segment. A computer cannot choose truly random numbers, so the sketch seeds the random number generator from a floating analog pin and, on each press, from the exact microsecond of your press, which you cannot repeat. random(1, 7) picks a number from 1 to 6. The spin animation runs a light round the outer segments and slows down, like a die losing speed. Try wiring a second display for a pair of dice.

Runs on a virtual Arduino Uno in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// Segments a to g are on pins 2 to 8. Bit 0 of a pattern is segment a, bit 6 is segment g.
const uint8_t SEG_PIN[7] = {2, 3, 4, 5, 6, 7, 8};
const uint8_t BTN = 9;

const uint8_t DIGIT[7] = {
  0x3F,   // 0  a b c d e f
  0x06,   // 1  b c
  0x5B,   // 2  a b d e g
  0x4F,   // 3  a b c d g
  0x66,   // 4  b c f g
  0x6D,   // 5  a c d f g
  0x7D    // 6  a c d e f g
};

void show(uint8_t pattern) {
  for (uint8_t i = 0; i < 7; i++) digitalWrite(SEG_PIN[i], (pattern >> i) & 1);
}

void spin() {
  // Light the outer segments a, b, c, d, e, f in turn, slowing down like a rolling die.
  uint16_t gap = 40;
  for (uint8_t n = 0; n < 24; n++) {
    show(1 << (n % 6));
    delay(gap);
    gap += 6;
  }
}

void setup() {
  for (uint8_t i = 0; i < 7; i++) pinMode(SEG_PIN[i], OUTPUT);
  pinMode(BTN, INPUT_PULLUP);
  randomSeed(analogRead(A0));
  show(DIGIT[6]);                       // start by showing a 6
}

void loop() {
  if (digitalRead(BTN) == LOW) {
    randomSeed(micros() + analogRead(A0));   // timing of your press adds real randomness
    spin();
    uint8_t roll = random(1, 7);              // 1 to 6
    show(DIGIT[roll]);
    while (digitalRead(BTN) == LOW) delay(10);
    delay(50);
  }
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Power onShows 6
Press the buttonSpinning animation for about a second
After the spinA single digit 1 to 6
Twenty rollsNo digit missing or repeated always
Hold the buttonNo extra rolls until released

If it does not work

Some segments never light

Check the pin order and that each resistor is in the circuit.

Wrong digit shapes

The display may be common anode, invert the pattern bits with a tilde.

Segments are dim

Use 220 ohm instead of 330 ohm resistors.

Same number appears often

Leave A0 unconnected so it floats.

Display lights all segments always

The common pin is not connected to GND.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the electronic dice?

Arduino Uno R3, 7-segment display 1 digit (common cathode), Resistor 330 Ω × 7, Tactile push button 6 mm, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).

How long does the electronic dice take to build?

About 60 minutes for a beginner maker, in 8 steps.

How do I know the electronic dice works?

Power on: Shows 6. Press the button: Spinning animation for about a second. After the spin: A single digit 1 to 6.

Some segments never light: what should I check?

Check the pin order and that each resistor is in the circuit.

Wrong digit shapes: what should I check?

The display may be common anode, invert the pattern bits with a tilde.

Segments are dim: what should I check?

Use 220 ohm instead of 330 ohm resistors.

Same number appears often: what should I check?

Leave A0 unconnected so it floats.