Projects / Series and parallel resistors

Series and parallel resistors

Combine resistors in series and parallel, predict the total, then measure it.

Beginner30 minGuided buildReviewed

Build it step by step

0 of 6 done
  1. Read each resistor

    Check the colour bands and the meter value of every resistor.

  2. Series

    Join two 1 kΩ in a line and predict 2 kΩ. Measure.

  3. Parallel

    Put two 1 kΩ side by side and predict 500 Ω. Measure.

  4. Three resistors

    Do three 1 kΩ in series and then in parallel, predict first.

  5. Mixed network

    Build the mixed network from the table and predict 361 Ω, then measure.

  6. Explain differences

    Resistors are 5 % off, so a difference of a few percent is normal.

In short

How do you build a series and parallel resistors?

Combine resistors in series and parallel, predict the total, then measure it. You need Digital multimeter, Resistor 1 kΩ × 4, Resistor 10 kΩ × 2, Resistor 220 Ω × 2 and Breadboard 830 Tie Points. It takes 6 steps and about 30 minutes.

Level
Beginner
Time
About 30 min
Parts
5
See the electronics first. This build uses resistors in series. Try resistors in series in the circuit builder and watch the voltages and currents before you wire it.

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Series testTwo 1 kΩ resistors end to end, meter across bothPredict 2 kΩ
Parallel testTwo 1 kΩ resistors side by side, meter across bothPredict 500 Ω
Mixed networkTwo 1 kΩ in series, in parallel with two 220 Ω in seriesPredict about 361 Ω
MeterOhms range, probes on the two endsDo not touch both probe tips with your fingers

No code needed

No code. Series: R = R1 + R2. Parallel: 1/R = 1/R1 + 1/R2, so two equal resistors halve the value. The mixed network is (1 kΩ + 1 kΩ) in parallel with (220 Ω + 220 Ω), which is 2000 Ω in parallel with 440 Ω, about 361 Ω.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Two 1 kΩ in seriesAbout 2.0 kΩ
Two 1 kΩ in parallelAbout 500 Ω
Three 1 kΩ in parallelAbout 333 Ω
Mixed networkAbout 361 Ω

If it does not work

Reading is lower than expected

Your fingers are in parallel with the resistor. Hold only the leads' insulated bodies.

Reading unstable

The probes are not touching firmly. Press them on the leads.

Big difference from calculation

The wrong resistor or a misread band. Measure each one first.

Meter shows OL

The circuit is open. Check the connections on the breadboard.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the series and parallel resistors?

Digital multimeter, Resistor 1 kΩ × 4, Resistor 10 kΩ × 2, Resistor 220 Ω × 2 and Breadboard 830 Tie Points.

How long does the series and parallel resistors take to build?

About 30 minutes for a beginner maker, in 6 steps.

How do I know the series and parallel resistors works?

Two 1 kΩ in series: About 2.0 kΩ. Two 1 kΩ in parallel: About 500 Ω. Three 1 kΩ in parallel: About 333 Ω.

Reading is lower than expected: what should I check?

Your fingers are in parallel with the resistor. Hold only the leads' insulated bodies.

Reading unstable: what should I check?

The probes are not touching firmly. Press them on the leads.

Big difference from calculation: what should I check?

The wrong resistor or a misread band. Measure each one first.

Meter shows OL: what should I check?

The circuit is open. Check the connections on the breadboard.