Projects / Pet door that knows your cat

Pet door that knows your cat

Intermediate3 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. NANO

    Read your tag

    Print the ID.

  2. NANO59°

    Build the latch

    Servo bolt on the outer side only.

  3. NANORDM6300

    Test unlocking

    Hold the tag to the reader.

  4. NANO

    Add the pass sensor

    Relock after the pet passes.

  5. NANO

    Add the stay-in button

    Block entry on request.

  6. NANO

    Log visits

    Count in the sketch or on a card.

  7. NANO

    Test with the pet

    Be present for the first few days.

In short

How do you build a pet door that knows your cat?

An RFID reader on a cat flap lets only your pet in, keeping out strays. You need Arduino Nano, RDM6300 125 kHz RFID reader, 125 kHz RFID cards (EM4100), SG90 Micro Servo, IR obstacle avoidance sensor module, Battery holder 4 × AA with switch, AA alkaline battery × 4 and Tactile push button 6 mm. It takes 7 steps and about 180 minutes.

Level
Intermediate
Time
About 180 min
Parts
8

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
RDM6300 TXNano D2Tag data (3.3 V serial, safe for the Nano)
RDM6300 5V and GNDNano 5V and GNDPower
Servo signalNano D9Latch
Servo plus and minusBattery holder plus and minus6 V supply
Battery holder plusNano VINPower the Nano
IR sensor OUTNano D3Pass-through sensor
Stay-in buttonNano D4 to groundLock for the night
All groundsJoinedCommon ground

Code

The RDM6300 reads a 125 kHz collar tag from a few centimetres and sends its 10-character ID over serial; first run the sketch with MY_TAG left as zeros, hold your cat's tag to the reader, copy the ID from the Serial Monitor and put it in MY_TAG. The servo latch blocks only the outside of the flap, so your cat can always push out from inside, whatever the electronics do, which means the cat cannot be locked in or trapped; make sure the latch mechanically leaves the inside free. The stay-in button blocks entry, and it is up to you to keep it for the evening only if your cat can sleep safely inside. A 4 AA pack powers the servo directly at 6 V and feeds the Nano's VIN. Keep every connector out of the rain, and check the flap and the latch weekly. Never rely on this to keep a pet safe from dangerous animals or traffic, and ask your vet about the right microchip or tag. Arduino IDE, board "Arduino Nano" (try the Old Bootloader option if the upload fails).

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// Cat flap: unlock for your pet's tag only. RDM6300 frame: 0x02, 10 ASCII hex characters, 2 checksum characters, 0x03.
#include <SoftwareSerial.h>
#include <Servo.h>
SoftwareSerial rfid(2, 8);                            // RX on D2, TX unused
Servo latch;
const char* MY_TAG = "0000000000";                    // run once and read your tag's 10 characters from the Serial Monitor
const int IRPIN = 3, BTN = 4;
bool stayIn = false;
int visits = 0;
char buf[10];
void setup() {
  Serial.begin(9600); rfid.begin(9600);
  pinMode(IRPIN, INPUT); pinMode(BTN, INPUT_PULLUP);
  latch.attach(9); latch.write(0);                    // 0 = latched
}
bool readTag() {
  if (!rfid.available() || rfid.read() != 0x02) return false;
  for (int i = 0; i < 10; i++) { unsigned long t = millis(); while (!rfid.available()) if (millis() - t > 100) return false; buf[i] = rfid.read(); }
  while (rfid.available()) rfid.read();               // discard checksum and end byte
  return true;
}
void loop() {
  if (digitalRead(BTN) == LOW) { stayIn = !stayIn; delay(500); Serial.println(stayIn ? "Stay-in ON" : "Stay-in OFF"); }
  if (readTag()) {
    char id[11]; memcpy(id, buf, 10); id[10] = 0;
    Serial.print("Tag: "); Serial.println(id);
    if (!stayIn && strcmp(id, MY_TAG) == 0) {
      latch.write(90); visits++;                      // unlock the entry side
      unsigned long t = millis();
      while (millis() - t < 6000UL) {                 // stay open for 6 s, or until the pet has passed
        if (digitalRead(IRPIN) == LOW) { delay(2000); break; }
      }
      latch.write(0);
    }
  }
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Your tagLatch opens for six seconds
Another tagStays latched
Stay-in buttonEntry blocked
Pushing out from insideAlways free

If it does not work

Tag not read

Hold it flat near the coil.

Servo buzzes

Check the latch travel.

No ID in the monitor

Check D2 and the baud rate of 9600.

Door relocks too early

Lengthen the open time.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the pet door that knows your cat?

Arduino Nano, RDM6300 125 kHz RFID reader, 125 kHz RFID cards (EM4100), SG90 Micro Servo, IR obstacle avoidance sensor module, Battery holder 4 × AA with switch, AA alkaline battery × 4 and Tactile push button 6 mm.

How long does the pet door that knows your cat take to build?

About 180 minutes for a intermediate maker, in 7 steps.

How do I know the pet door that knows your cat works?

Your tag: Latch opens for six seconds. Another tag: Stays latched. Stay-in button: Entry blocked.

Tag not read: what should I check?

Hold it flat near the coil.

Servo buzzes: what should I check?

Check the latch travel.

No ID in the monitor: what should I check?

Check D2 and the baud rate of 9600.

Door relocks too early: what should I check?

Lengthen the open time.