Projects / Roaming pet toy robot

Roaming pet toy robot

Intermediate2.5 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. NANOROBOT

    Build the chassis

    Motors, driver and battery pack.

  2. NANO

    Test driving

    Forward, back and turns.

  3. NANO56 cm

    Add the obstacle turn

    Ultrasonic sensor and random turns.

  4. NANO

    Add the tilt stop

    Motors off when lifted.

  5. NANO59°

    Build the treat flap

    Servo and a tiny hopper.

  6. NANO

    Add the timing

    One treat every 20 minutes.

  7. NANO

    Play test

    With your cat and supervision.

In short

How do you build a roaming pet toy robot?

A small robot wanders and drops a treat, avoiding walls, to entertain a cat. You need Arduino Nano, HC-SR04 Ultrasonic Sensor, TB6612FNG Motor Driver, BO motor straight 100 RPM × 2, Robot car chassis kit 2WD (acrylic), SG90 Micro Servo, Battery holder 4 × AA with switch, AA alkaline battery × 4, Tilt sensor (ball switch, SW-520D) and Active buzzer 5 V. It takes 7 steps and about 150 minutes.

Level
Intermediate
Time
About 150 min
Parts
10

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
HC-SR04 TRIG and ECHONano D12 and D13Obstacle sensor
HC-SR04 VCC and GNDNano 5V and GNDPower
TB6612 PWMA, AIN1, AIN2Nano D5, D7, D8Left motor
TB6612 PWMB, BIN1, BIN2Nano D6, D9, D10Right motor
TB6612 STBYNano D11Driver enable
Servo signalNano D3Treat flap
Tilt switchNano D4 and GNDPick-up detector
BuzzerNano D2 and GNDSound
Battery pack plusTB6612 VM, Nano VIN and servo plus6 V supply

Code

The robot drives forward with a small random wobble, and when the ultrasonic sensor sees something within 20 cm it backs up and turns a random way for a random time, so it never follows the same path. Every 20 minutes it stops, chirps and tips a treat out of a hopper through a servo flap; keep the hopper very small, so a stuck mechanism can never overfeed your pet. If the tilt switch opens because the robot was lifted or has tipped over, the motors stop at once. Use only pet-safe materials, with no small parts a cat can pull off, cover wires, and keep the speed low; the cat should never be able to reach the wheels or batteries. Supervise play and put the robot away afterwards. Cats may find the sound or movement stressful, so introduce it slowly and stop if your pet seems upset. Arduino IDE, board "Arduino Nano" (try the Old Bootloader option if the upload fails).

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// Roaming pet robot: wanders, turns away from obstacles, drops a treat now and then, stops when lifted. Board: Arduino Nano.
#include <Servo.h>
Servo flap;
const int TRIG = 12, ECHO = 13, TILT = 4, BUZ = 2;
const int PWMA = 5, AIN1 = 7, AIN2 = 8, PWMB = 6, BIN1 = 9, BIN2 = 10, STBY = 11;
const unsigned long TREAT_EVERY = 20UL * 60UL * 1000UL;   // one treat every 20 minutes
unsigned long lastTreat = 0;
void drive(int l, int r) {
  digitalWrite(AIN1, l > 0); digitalWrite(AIN2, l < 0); analogWrite(PWMA, abs(l));
  digitalWrite(BIN1, r > 0); digitalWrite(BIN2, r < 0); analogWrite(PWMB, abs(r));
}
long distanceCm() {
  digitalWrite(TRIG, LOW); delayMicroseconds(3);
  digitalWrite(TRIG, HIGH); delayMicroseconds(10); digitalWrite(TRIG, LOW);
  long us = pulseIn(ECHO, HIGH, 20000);
  return us ? us / 58 : 200;
}
void setup() {
  int pins[] = {PWMA, AIN1, AIN2, PWMB, BIN1, BIN2, STBY, TRIG, BUZ};
  for (int i = 0; i < 9; i++) pinMode(pins[i], OUTPUT);
  pinMode(ECHO, INPUT); pinMode(TILT, INPUT_PULLUP);
  digitalWrite(STBY, HIGH);
  flap.attach(3); flap.write(0);
  randomSeed(analogRead(A0));
}
void loop() {
  if (digitalRead(TILT) == HIGH) { drive(0, 0); return; }     // lifted or tipped: stop at once
  if (millis() - lastTreat > TREAT_EVERY) {
    drive(0, 0); lastTreat = millis();
    tone(BUZ, 1200, 200); delay(300);
    flap.write(70); delay(600); flap.write(0);                 // flap opens and a treat rolls out
  }
  long d = distanceCm();
  if (d < 20) {                                                // wall ahead: back up and turn a random way
    drive(-130, -130); delay(400);
    if (random(2)) drive(140, -140); else drive(-140, 140);
    delay(random(300, 700));
  } else {
    drive(130 + random(-20, 20), 130 + random(-20, 20));       // gentle wobble so the path varies
    delay(150);
  }
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Open floorWanders with a varying path
Wall aheadBacks up and turns
Picked upMotors stop
Treat timeChirp and one treat drops

If it does not work

Spins on the spot

Check the motor wiring direction.

Hits walls

Check the sensor aim and raise the 20 cm distance.

Flap stuck

Adjust the servo angle.

Does not stop when lifted

Check the tilt switch orientation.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the roaming pet toy robot?

Arduino Nano, HC-SR04 Ultrasonic Sensor, TB6612FNG Motor Driver, BO motor straight 100 RPM × 2, Robot car chassis kit 2WD (acrylic), SG90 Micro Servo, Battery holder 4 × AA with switch, AA alkaline battery × 4, Tilt sensor (ball switch, SW-520D) and Active buzzer 5 V.

How long does the roaming pet toy robot take to build?

About 150 minutes for a intermediate maker, in 7 steps.

How do I know the roaming pet toy robot works?

Open floor: Wanders with a varying path. Wall ahead: Backs up and turns. Picked up: Motors stop.

Spins on the spot: what should I check?

Check the motor wiring direction.

Hits walls: what should I check?

Check the sensor aim and raise the 20 cm distance.

Flap stuck: what should I check?

Adjust the servo angle.

Does not stop when lifted: what should I check?

Check the tilt switch orientation.