Projects / Moving cat ears headband

Moving cat ears headband

Beginner2 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. XIAO59°

    Test a servo

    Move it to 60, 90 and 120 degrees.

  2. XIAO

    Mount on the headband

    Fix both with foam and zip ties.

  3. XIAO

    Write the poses

    Happy, curious, sleepy.

  4. XIAO

    Add the button

    Cycle moods.

  5. XIAOKY038

    Add the sound sensor

    Startle on a clap.

  6. XIAO+

    Add the battery

    Fit the LiPo in a pouch.

  7. XIAO

    Cover moving parts

    Foam over horns and gaps.

In short

How do you build a moving cat ears headband?

Two servos move cat ears on a headband to match a mood picked with a button or triggered by sound. You need Seeed XIAO RP2040, SG90 Micro Servo × 2, Sound sensor module (KY-038), Tactile push button 6 mm and Li-Po battery 3.7 V 1000 mAh. It takes 7 steps and about 120 minutes.

Level
Beginner
Time
About 120 min
Parts
5

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Left servo signalXIAO D0Left ear
Right servo signalXIAO D1Right ear
Servos plus and minusLiPo plus (through the XIAO BAT pads) and GNDServo power (small 9 g servos work on 3.7 V)
Sound module VCC and GNDXIAO 3V3 and GNDPower
Sound module AOXIAO D2 (analog)Loudness
ButtonXIAO D3 and GNDNext mood
LiPoXIAO BAT padsPower and charging

Code

Two small servos move the ears in small steps, so they stay gentle. The moods are short animations picked with the button, and a loud sound makes both ears perk up for a moment. Use two 9 g micro servos on a light headband, keep every moving part away from hair, ears and eyes, and cover the servo horns with soft foam so nothing can pinch. The servos draw current in short bursts, so powering them straight from a LiPo (3.7 V) works for micro servos but they move slowly; do not use stronger servos. Use a protected LiPo, tuck it in a pouch and never wear the headband while it charges. Take it off if anything feels uncomfortable, and supervise young children. Sound sensitivity is set by the module's small screw. Arduino IDE with the Raspberry Pi Pico/RP2040 boards package by Earle Philhower, board "Seeed XIAO RP2040".

Runs on a virtual Seeed XIAO RP2040 in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// Cat ears: moods and a startle on loud sound. Board: Seeed XIAO RP2040. Library: Servo (built into the RP2040 core).
#include <Servo.h>
Servo L, R;
const int SND = D2, BTN = D3;
int mood = 0; unsigned long lastBtn = 0, lastTwitch = 0;

void pose(int l, int r, int ms) {                 // move gently to a pose in small steps
  int cl = L.read(), cr = R.read();
  for (int i = 1; i <= 20; i++) { L.write(cl + (l - cl) * i / 20); R.write(cr + (r - cr) * i / 20); delay(ms / 20); }
}

void setup() {
  L.attach(D0); R.attach(D1);
  pinMode(BTN, INPUT_PULLUP);
  L.write(90); R.write(90);
}

void loop() {
  if (!digitalRead(BTN) && millis() - lastBtn > 300) { mood = (mood + 1) % 3; lastBtn = millis(); }
  if (analogRead(SND) > 800) {                    // a loud noise: perk both ears up quickly
    pose(130, 50, 200); delay(600); pose(90, 90, 400);
  }
  switch (mood) {
    case 0: // happy: ears perk up and down together
      pose(120, 60, 500); pose(90, 90, 500); break;
    case 1: // curious: one ear at a time
      pose(120, 90, 400); delay(300); pose(90, 60, 400); delay(300); break;
    case 2: // sleepy: ears droop slowly
      pose(60, 120, 1500); delay(2000); pose(80, 100, 1500); delay(2000); break;
  }
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Press the buttonMood changes
ClapEars perk up for a moment
Sleepy moodSlow droop and rise
Battery onWorks for an hour or more

If it does not work

Ears jitter

Add a capacitor across the servo supply and check the ground.

Reset on movement

Use a better battery or slower moves.

Always startled

Turn the module's screw to lower sensitivity.

Servos too weak

Reduce the ear weight.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the moving cat ears headband?

Seeed XIAO RP2040, SG90 Micro Servo × 2, Sound sensor module (KY-038), Tactile push button 6 mm and Li-Po battery 3.7 V 1000 mAh.

How long does the moving cat ears headband take to build?

About 120 minutes for a beginner maker, in 7 steps.

How do I know the moving cat ears headband works?

Press the button: Mood changes. Clap: Ears perk up for a moment. Sleepy mood: Slow droop and rise.

Ears jitter: what should I check?

Add a capacitor across the servo supply and check the ground.

Reset on movement: what should I check?

Use a better battery or slower moves.

Always startled: what should I check?

Turn the module's screw to lower sensitivity.

Servos too weak: what should I check?

Reduce the ear weight.