Projects / Twist, pull, press reaction game

Twist, pull, press reaction game

Intermediate2.5 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. NANO

    Test each control

    Print the three readings.

  2. NANOSANDIS

    Prepare the card

    Record five short tracks.

  3. NANO

    Test the player

    Play each track from code.

  4. NANO

    Detect the actions

    Print which control moved.

  5. NANO

    Build one round

    Prompt, wait, and judge.

  6. NANO

    Add speeding up and scoring

    Shorten the limit each round.

  7. NANO

    Box it

    Mount the controls on a lid.

In short

How do you build a twist, pull, press reaction game?

The game calls out press it, twist it or pull it, and you must do the action in time. You need Arduino Nano, Tactile push button 6 mm, Potentiometer 10 kΩ, Slide potentiometer 10 kΩ, DFPlayer Mini MP3 module, Speaker 8 Ω 0.5 W, SanDisk microSD card 32 GB (A1, Class 10), Battery holder 4 × AA with switch and Resistor 1 kΩ. It takes 7 steps and about 150 minutes.

Level
Intermediate
Time
About 150 min
Parts
9

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
ButtonNano D2 and GNDPress it
Twist pot wiperNano A0 (ends to 5 V and GND)Twist it
Slide pot wiperNano A1 (ends to 5 V and GND)Pull it
DFPlayer TXNano D10Replies
DFPlayer RXNano D11 through a 1 kΩ resistorCommands
DFPlayer SPK1 and SPK2SpeakerVoice and sounds
4 AA holderNano VIN and GND, DFPlayer VCC to Nano 5V6 V battery power

Code

Each round picks an action at random, plays its voice from the SD card, and gives you a time limit that shortens by about 0.1 second every round. The code compares the resting positions of the pot and slider with their new positions, so you must move the right control by a good margin. The wrong control moving counts as a loss. Record your own voice prompts as short MP3 files with the names shown, in FAT32. Wait for the button to be released between rounds, or a held button would count as the next action. Keep the volume moderate. Power from 4 AA cells through the Nano's VIN pin; do not feed the DFPlayer from VIN, use the Nano's 5 V pin. For a young child's toy, enclose the batteries so the cover needs a screwdriver. Arduino IDE, board "Arduino Nano" (try the Old Bootloader option if the upload fails).

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// Twist, pull, press game. Libraries: DFRobotDFPlayerMini. Board: Arduino Nano.
// SD card tracks: 0001 "Press it", 0002 "Twist it", 0003 "Pull it", 0004 success sound, 0005 game over.
#include <SoftwareSerial.h>
#include <DFRobotDFPlayerMini.h>

SoftwareSerial mp3(10, 11);
DFRobotDFPlayerMini player;
const int BTN = 2, TWIST = A0, SLIDE = A1;
int baseTwist, baseSlide, score = 0;
unsigned long timeLimit = 3000;

void rebase() { baseTwist = analogRead(TWIST); baseSlide = analogRead(SLIDE); }

int readAction() {                              // returns 0 press, 1 twist, 2 pull, or -1 for nothing
  if (!digitalRead(BTN)) return 0;
  if (abs(analogRead(TWIST) - baseTwist) > 250) return 1;
  if (abs(analogRead(SLIDE) - baseSlide) > 250) return 2;
  return -1;
}

void setup() {
  pinMode(BTN, INPUT_PULLUP);
  mp3.begin(9600); player.begin(mp3); player.volume(20);
  randomSeed(analogRead(A5));
  rebase();
}

void loop() {
  rebase(); delay(300);                         // read the resting position of the two controls
  while (!digitalRead(BTN)) {}                  // wait for the button to be released first
  int want = random(3);
  player.play(want + 1);                        // say the action
  unsigned long start = millis(); int got = -1;
  while (millis() - start < timeLimit && got < 0) got = readAction();
  if (got == want) {
    score++; player.play(4); delay(500);
    if (timeLimit > 900) timeLimit -= 120;      // speed up every round
  } else {
    player.play(5);                             // wrong action or too slow: game over
    delay(2500); score = 0; timeLimit = 3000;
  }
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Hear Press it and press the buttonSuccess sound
Hear Twist it and press the buttonGame over
Do nothingGame over after the limit
Several correct roundsPrompts come faster

If it does not work

Random game over

Increase the movement margin or check for noisy pots.

No voice

Check the SD card format and the file names.

Prompt repeats too fast

Add a delay after the success sound.

Resets

Use fresh batteries and a good ground.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the twist, pull, press reaction game?

Arduino Nano, Tactile push button 6 mm, Potentiometer 10 kΩ, Slide potentiometer 10 kΩ, DFPlayer Mini MP3 module, Speaker 8 Ω 0.5 W, SanDisk microSD card 32 GB (A1, Class 10), Battery holder 4 × AA with switch and Resistor 1 kΩ.

How long does the twist, pull, press reaction game take to build?

About 150 minutes for a intermediate maker, in 7 steps.

How do I know the twist, pull, press reaction game works?

Hear Press it and press the button: Success sound. Hear Twist it and press the button: Game over. Do nothing: Game over after the limit.

Random game over: what should I check?

Increase the movement margin or check for noisy pots.

No voice: what should I check?

Check the SD card format and the file names.

Prompt repeats too fast: what should I check?

Add a delay after the success sound.

Resets: what should I check?

Use fresh batteries and a good ground.