Build it step by step
0 of 8 doneChoose the three resistors
Note the values secretly.
Join them at the centre
Three arms to one point.
Bring out three terminals
A, B and C on the terminal block.
Cover the centre
Only the terminals show.
Measure the pairs
Rab, Rbc and Rac.
Solve
Use the three equations.
Reveal
Check against the real values.
Try the triangle
Rebuild as a delta and repeat.
How do you build a resistor mystery box?
A hidden network of resistors behind three terminals is worked out by measuring between each pair with a meter. You need Resistor 1 kΩ × 3, Resistor 10 kΩ × 2, Resistor 330 Ω, Screw terminal block 3-pin (5 mm), Digital multimeter, Jumper wires male to male (40 pcs, 20 cm) and Breadboard 830 Tie Points. It takes 8 steps and about 60 minutes.
- Level
- Beginner
- Time
- About 60 min
- Parts
- 7
Parts list
- PassivesBuyResistor 1 kΩ × 3
- PassivesBuyResistor 10 kΩ × 2
- PassivesBuyResistor 330 Ω × 1
- ConnectorsBuy
- Tools & InstrumentsBuy
- PrototypingBuy
- PrototypingBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| Resistor Ra (1 kilohm) | Terminal A to the hidden centre point | First arm |
| Resistor Rb (10 kilohm) | Terminal B to the hidden centre point | Second arm |
| Resistor Rc (330 ohm) | Terminal C to the hidden centre point | Third arm |
| Three arms joined at one point | Under a cover or card, not reachable | The centre point |
| 3-pin screw terminal block | Terminals A, B and C only | What the solver can touch |
| Multimeter | Between pairs of terminals, unpowered | Ohms range |
Code
A hidden network is a good way to practise the most useful rules of resistors: resistances in series add, and the meter reads the total between any two terminals. Here three resistors are joined at one point you cannot reach, and only the three outer ends are brought out to a terminal block. One person builds the box and keeps the values secret, and the other measures between the three pairs of terminals with the meter on its ohms range and writes three equations, one for each pair. Each reading is the sum of two of the three resistors, so a little algebra separates them: add two of the readings, subtract the third, and divide by two to get the resistor that the first two share. The solved values should come out close to the real ones, within the tolerance of the resistors, which is a good way to see that a 5 percent resistor really can be 5 percent off. Measure the resistors alone beforehand and compare. The power must always be off when you measure resistance, because a live circuit confuses the meter and can damage it. As an extension, rebuild the box with the same three resistors in a triangle, where each reading is one resistor in parallel with the other two in series, and see that the solving method has to change. This is the same star and delta conversion used in power engineering and filter design.
Build notes (no code needed for this build) The box: three resistors joined at a hidden centre point, with only terminals A, B and C reachable. This is a star (T) network. The builder uses Ra = 1 kilohm (to A), Rb = 10 kilohm (to B) and Rc = 330 ohm (to C), and keeps the values secret. Solver: measure between each pair with the circuit unpowered, on the ohms range: Rab = Ra + Rb Rbc = Rb + Rc Rac = Ra + Rc Solve (add and subtract the three equations): Ra = (Rab + Rac - Rbc) / 2 Rb = (Rab + Rbc - Rac) / 2 Rc = (Rbc + Rac - Rab) / 2 Worked example with the values above (calculated): Rab = 11.0 kilohm, Rbc = 10.33 kilohm, Rac = 1.33 kilohm. Ra = (11.0 + 1.33 - 10.33) / 2 = 1.0 kilohm Rb = (11.0 + 10.33 - 1.33) / 2 = 10 kilohm Rc = (10.33 + 1.33 - 11.0) / 2 = 0.33 kilohm Real readings differ by the resistor tolerance (5 percent), so the solved values land within 5 to 10 percent of the true ones. Measure the resistors alone first, then compare. Extension: wire the three resistors as a triangle (delta) between A, B and C instead, measure again, and show that the equations change. In a triangle, each pair reads one resistor in parallel with the other two in series, so Rab = Rab_res x (Rbc_res + Rac_res) / (sum of all three).
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Rab | About 11 kilohm for 1k and 10k |
| Rbc | About 10.3 kilohm |
| Rac | About 1.3 kilohm |
| Solved Ra | Within about 10 percent of 1 kilohm |
| Solved Rc | Close to 330 ohm, with more error for small values |
If it does not work
Readings drift
Power is still connected, remove it.
Rab smaller than expected
A hidden wire shorts two arms.
Solved value is negative
Check which reading is which pair.
Small resistor has a large error
The meter lead resistance matters, short the leads first.
Terminal readings do not match
Check each resistor is joined at the centre point.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the resistor mystery box?
Resistor 1 kΩ × 3, Resistor 10 kΩ × 2, Resistor 330 Ω, Screw terminal block 3-pin (5 mm), Digital multimeter, Jumper wires male to male (40 pcs, 20 cm) and Breadboard 830 Tie Points.
How long does the resistor mystery box take to build?
About 60 minutes for a beginner maker, in 8 steps.
How do I know the resistor mystery box works?
Rab: About 11 kilohm for 1k and 10k. Rbc: About 10.3 kilohm. Rac: About 1.3 kilohm.
Readings drift: what should I check?
Power is still connected, remove it.
Rab smaller than expected: what should I check?
A hidden wire shorts two arms.
Solved value is negative: what should I check?
Check which reading is which pair.
Small resistor has a large error: what should I check?
The meter lead resistance matters, short the leads first.
