Projects / RC time constant lab

RC time constant lab

Beginner45 minGuided buildReviewed

Build it step by step

0 of 6 done
  1. Check the parts

    Measure the resistor with the meter. Note the capacitor's rating is at least 16 V.

  2. +

    Build the circuit

    Battery +, button, 10 kΩ, capacitor +, and back to the battery - through the capacitor. Watch the polarity.

  3. Discharge the capacitor

    Put the 1 kΩ across it for 10 seconds, then remove it.

  4. Measure

    Set the meter to DC volts across the capacitor. Press and hold the button and read the voltage every 5 seconds with a phone stopwatch.

  5. Plot

    Draw voltage against time and find the time at which it reaches 5.7 V.

  6. Compare

    Is it near 10 s? Capacitors can be 20 % off, so allow some difference.

In short

How do you build an RC time constant lab?

Charge a capacitor through a resistor and time how long it takes to reach 63 %. You need Digital multimeter, Electrolytic capacitor 1000 µF, Resistor 10 kΩ, Resistor 1 kΩ, Tactile push button 6 mm, Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm), 9 V battery and 9 V battery snap with DC jack. It takes 6 steps and about 45 minutes.

Level
Beginner
Time
About 45 min
Parts
9
See the electronics first. This build uses capacitor charging. Try a capacitor charging in the circuit builder and watch the voltages and currents before you wire it.

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
9 V battery +Button, then 10 kΩCharge path
10 kΩ other endCapacitor + (long leg) and the DMM red probeCapacitor voltage
Capacitor - (stripe side)9 V battery - and the DMM black probeCommon
1 kΩ resistorAcross the capacitor with a jumper wire when you want to dischargeReset between runs

No code needed

No code. Time constant τ = R × C = 10 000 Ω × 0.001 F = 10 s. After one τ the capacitor reaches 63 % of the supply, which is about 5.7 V from a 9 V battery. The multimeter's input resistance (about 10 MΩ) is small enough to ignore.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
At 0 s0 V
At 10 sAbout 5.7 V (63 % of 9 V)
At 50 sClose to 9 V (more than 99 %)
Repeat with 1 kΩ in place of 10 kΩThe time constant is 1 s, ten times faster

If it does not work

Voltage rises far too slowly or stops short

The capacitor leaks or its tolerance is wide. Try another.

Reading rises then falls

The meter is draining the capacitor in a high range. Use the 10 MΩ input range.

Nothing happens

The capacitor is backwards or the button is not closing.

Capacitor gets warm or smells

It is connected backwards. Disconnect the battery at once.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the RC time constant lab?

Digital multimeter, Electrolytic capacitor 1000 µF, Resistor 10 kΩ, Resistor 1 kΩ, Tactile push button 6 mm, Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm), 9 V battery and 9 V battery snap with DC jack.

How long does the RC time constant lab take to build?

About 45 minutes for a beginner maker, in 6 steps.

How do I know the RC time constant lab works?

At 0 s: 0 V. At 10 s: About 5.7 V (63 % of 9 V). At 50 s: Close to 9 V (more than 99 %).

Voltage rises far too slowly or stops short: what should I check?

The capacitor leaks or its tolerance is wide. Try another.

Reading rises then falls: what should I check?

The meter is draining the capacitor in a high range. Use the 10 MΩ input range.

Nothing happens: what should I check?

The capacitor is backwards or the button is not closing.

Capacitor gets warm or smells: what should I check?

It is connected backwards. Disconnect the battery at once.