Projects / Kirchhoff's laws lab

Kirchhoff's laws lab

Intermediate1 hGuided buildReviewed

Build it step by step

0 of 8 done
  1. Measure the sources

    Read V1 and V2 with the meter and write them down.

  2. Build the circuit

    Wire R1, R2, R3 and the two batteries as in the table.

  3. Calculate first

    Work out the expected node voltage and the three currents from your measured V1 and V2.

  4. Measure the node voltage

    Read it from node N to ground.

  5. Measure the currents

    Break each branch in turn and put the meter in series.

  6. Check the node

    Current into N from R1 and R3 should equal the current out through R2.

  7. Check the loop

    The drops across R1 and R2 should add up to V1.

  8. Check the other loop

    The drops across R3 and R2 should add up to V2.

In short

How do you build a kirchhoff's laws lab?

Measure currents into a node and voltages around a loop to check Kirchhoff's laws. You need Digital multimeter, Resistor 1 kΩ, Resistor 2.2 kΩ, Resistor 4.7 kΩ, Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm), 9 V battery × 2 and 9 V battery snap with DC jack × 2. It takes 8 steps and about 60 minutes.

Level
Intermediate
Time
About 60 min
Parts
8
See the electronics first. This build uses resistors in series. Try resistors in series in the circuit builder and watch the voltages and currents before you wire it.

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Battery 1 + (V1)1 kΩ resistor R1, other end to node NFirst source
Battery 2 + (V2)4.7 kΩ resistor R3, other end to node NSecond source
Node N2.2 kΩ resistor R2 to the ground railShared branch
Battery 1 - and battery 2 -Ground railCommon return
MultimeterIn series in each branch for currents, across each part for voltagesMeasurements

No code needed

No code. Two 9 V batteries feed one node through R1 = 1 kΩ and R3 = 4.7 kΩ, and a single 2.2 kΩ resistor R2 takes the current to ground. With ideal 9 V sources the node voltage works out to about 6.55 V, giving about 2.45 mA through R1, 0.52 mA through R3 and 2.98 mA through R2, so the two incoming currents add up to the outgoing one (Kirchhoff's current law). Around the loop through V1, R1 and R2 the voltage drops add to 9 V (Kirchhoff's voltage law). Real batteries read slightly different from 9 V, so use your own measured source voltages in the calculation. Measure current only with the meter in series and on the mA range; never put it across a battery or a resistor on that range.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Node voltageAbout 6.5 V with fresh batteries
Current in R1About 2.4 mA
Current in R3About 0.5 mA
Current in R2About the sum of the other two, within a few percent

If it does not work

Currents do not add up

Check the meter range and the lead sockets; the meter itself adds a little resistance.

No current reading

A fuse in the meter may have blown, or the lead is in the wrong socket.

Voltages higher than expected

Check the resistor values with the meter.

Readings drift

Batteries are loaded lightly but may be old; try fresh ones.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the kirchhoff's laws lab?

Digital multimeter, Resistor 1 kΩ, Resistor 2.2 kΩ, Resistor 4.7 kΩ, Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm), 9 V battery × 2 and 9 V battery snap with DC jack × 2.

How long does the kirchhoff's laws lab take to build?

About 60 minutes for a intermediate maker, in 8 steps.

How do I know the kirchhoff's laws lab works?

Node voltage: About 6.5 V with fresh batteries. Current in R1: About 2.4 mA. Current in R3: About 0.5 mA.

Currents do not add up: what should I check?

Check the meter range and the lead sockets; the meter itself adds a little resistance.

No current reading: what should I check?

A fuse in the meter may have blown, or the lead is in the wrong socket.

Voltages higher than expected: what should I check?

Check the resistor values with the meter.

Readings drift: what should I check?

Batteries are loaded lightly but may be old; try fresh ones.