Projects / Interactive rangoli light mat

Interactive rangoli light mat

Intermediate5 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. ESP3215.3 mA

    Plan the layout

    Number the LEDs on paper.

  2. ESP3215.3 mA

    Fix the strip

    In the rangoli pattern on a base board.

  3. ESP32

    Test every LED

    Run a colour wipe.

  4. ESP32FSR402

    Add the pressure pads

    FSR and 10 kΩ at each.

  5. ESP32

    Write the ripple

    A bright ring from the pressed pad.

  6. ESP32

    Cover with acrylic

    Frosted sheet over a thin foam layer.

  7. ESP32

    Seal the wiring

    Nothing exposed at the edges.

In short

How do you build an interactive rangoli light mat?

Addressable LEDs laid out in a rangoli design under frosted acrylic light up where people step, using pressure pads. You need ESP32 DevKit V1, WS2812B strip 5 m (30 LEDs/m), Force sensitive resistor FSR 402 × 6, Resistor 10 kΩ × 6, 5 V 2 A USB adapter, Resistor 330 Ω and Electrolytic capacitor 1000 µF. It takes 7 steps and about 300 minutes.

Level
Intermediate
Time
About 300 min
Parts
7

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Each FSRESP32 3V3 to one end, other end to an ADC pin and a 10 kΩ to groundPressure pads
Six pad nodesESP32 GPIO32, 33, 34, 35, 36, 39ADC inputs
ESP32 GPIO5330 Ω resistor to strip DINLED data
5 V adapter plus and minusStrip 5V and GNDLED power
1000 µF capacitorAcross the strip 5V and GNDAbsorbs switching spikes
ESP32 GNDStrip GNDCommon ground
ESP32 VIN5 V adapter plusPower the board

Code

Lay the strip in your rangoli pattern under frosted acrylic, number the LEDs along its length, and note which LED is nearest each pressure pad; type those numbers into PAD_LED. When a pad is stepped on, a bright ring spreads outward from its LED along the strip while the rest slowly cycles through colours at low brightness. The FSR with a 10 kΩ resistor forms a divider: the harder you press, the higher the voltage on the pin. The six pad pins are all on ADC1, which still works when Wi-Fi is on. Keep brightness at about 30 percent, which stays cool under acrylic and uses only about 1 A for 60 LEDs. Use a 5 V 3 A adapter with the capacitor and the 330 Ω resistor in place, seal all joints under the mat so no one can touch a wire, keep it dry and indoor, and test the mat can take a person's weight on a plywood base. The effect fades slowly with no strobing. Arduino IDE with the ESP32 boards package 2.0.x, board "ESP32 Dev Module".

Runs on a virtual ESP32 Dev Module in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// Rangoli mat: pressure pads start colour ripples across the LED strip. Library: FastLED. Board: ESP32 Dev Module.
#include <FastLED.h>
#define NUM_LEDS 60
CRGB leds[NUM_LEDS];
const int PAD[6] = {32, 33, 34, 35, 36, 39};
const int PAD_LED[6] = {5, 15, 25, 35, 45, 55};       // which LED sits at each pad: set from your layout
int ripple[6];                                        // radius of the active ripple for each pad, or -1
uint8_t hueBase = 0;
void setup() {
  FastLED.addLeds<WS2812B, 5, GRB>(leds, NUM_LEDS);
  FastLED.setBrightness(80);                          // keeps current and heat low
  for (int i = 0; i < 6; i++) ripple[i] = -1;
}
void loop() {
  for (int i = 0; i < NUM_LEDS; i++) leds[i] = CHSV(hueBase + i * 3, 255, 60);   // slow colour cycle
  hueBase++;
  for (int p = 0; p < 6; p++) {
    if (analogRead(PAD[p]) > 1200 && ripple[p] < 0) ripple[p] = 0;                  // new press
    if (ripple[p] >= 0) {
      for (int i = 0; i < NUM_LEDS; i++) {
        int d = abs(i - PAD_LED[p]);
        if (abs(d - ripple[p]) <= 1) leds[i] = CHSV(hueBase + p * 40, 200, 255);    // bright ring
      }
      ripple[p]++;
      if (ripple[p] > NUM_LEDS) ripple[p] = -1;
    }
  }
  FastLED.show();
  delay(30);
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
IdleSlow colour cycle
Press a padRing spreads along the strip
Two padsTwo rings at once
Cool after an hourWarm at most

If it does not work

Pads always on

Raise the threshold.

Pads never trigger

Use a thin hard spacer so the FSR is squeezed.

Wrong spot lights

Check the PAD_LED numbers.

LEDs flicker

Check the data resistor and the capacitor.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the interactive rangoli light mat?

ESP32 DevKit V1, WS2812B strip 5 m (30 LEDs/m), Force sensitive resistor FSR 402 × 6, Resistor 10 kΩ × 6, 5 V 2 A USB adapter, Resistor 330 Ω and Electrolytic capacitor 1000 µF.

How long does the interactive rangoli light mat take to build?

About 300 minutes for a intermediate maker, in 7 steps.

How do I know the interactive rangoli light mat works?

Idle: Slow colour cycle. Press a pad: Ring spreads along the strip. Two pads: Two rings at once.

Pads always on: what should I check?

Raise the threshold.

Pads never trigger: what should I check?

Use a thin hard spacer so the FSR is squeezed.

Wrong spot lights: what should I check?

Check the PAD_LED numbers.

LEDs flicker: what should I check?

Check the data resistor and the capacitor.