Projects / Infinity mirror clock

Infinity mirror clock

Intermediate4 hGuided buildReviewed

Build it step by step

0 of 8 done
  1. ESP3219.0 mA

    Cut and test the strip

    Light 60 pixels in a short test.

  2. ESP32

    Build the frame

    Make a ring frame with the mirror at the back.

  3. ESP32

    Mount the pixels

    Face them inward or forward, evenly spaced.

  4. ESP32

    Add the front mirror

    Fit the two-way film in front.

  5. ESP32

    Fill in Wi-Fi

    Replace the placeholders.

  6. ESP32

    Upload and orient

    Rotate the ring so pixel 0 is at the top.

  7. ESP32

    Check the hands

    Compare with your phone clock.

  8. ESP32

    Dim at night

    Check the brightness change at 22:00.

In short

How do you build an infinity mirror clock?

A ring of LEDs between a mirror and a two-way mirror makes an endless tunnel, with hands shown in colour. You need ESP32 DevKit V1, WS2812B strip 5 m (30 LEDs/m), 5 V 2 A USB adapter, Resistor 330 Ω and Electrolytic capacitor 1000 µF. It takes 8 steps and about 240 minutes.

Level
Intermediate
Time
About 240 min
Parts
5

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
5 V supply +Strip + and the 1000 µF capacitor +Strip power
5 V supply -Strip - and capacitor - and ESP32 GNDCommon ground
5 V supply +ESP32 VINPower the ESP32
ESP32 GPIO5330 Ω resistor then strip DINData line

Code

Cut 60 pixels from the strip and stick them in a ring just inside a frame with the LEDs facing forward. Behind the LEDs goes a normal mirror and in front a two-way (one-way) mirror film on glass or acrylic, spaced about 2 to 3 cm apart; the light bounces between them and seems to run into an endless tunnel. The hands are single coloured pixels: red for the hour, green for the minute and blue for the second, and where they overlap the later one wins. The code dims the ring at night, and it uses internet time so no hands need setting. At the 60 brightness cap the ring stays within a 2 A supply. Take care when cutting and bending acrylic and glass. Arduino IDE with the ESP32 boards package, board "ESP32 Dev Module".

Runs on a virtual ESP32 Dev Module in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// Library: Adafruit NeoPixel. 60 LEDs in a ring, LED 0 at the 12 o'clock position.
#include <WiFi.h>
#include <time.h>
#include <Adafruit_NeoPixel.h>

const char* WIFI_SSID = "YOUR_WIFI_NAME";
const char* WIFI_PASS = "YOUR_WIFI_PASSWORD";
Adafruit_NeoPixel ring(60, 5, NEO_GRB + NEO_KHZ800);

void setup() {
  ring.begin();
  WiFi.begin(WIFI_SSID, WIFI_PASS);
  unsigned long t = millis();
  while (WiFi.status() != WL_CONNECTED && millis() - t < 15000) delay(300);
  configTime(19800, 0, "pool.ntp.org");          // India time, change for yours
}

void loop() {
  time_t now = time(nullptr);
  struct tm* tm = localtime(&now);
  if (tm->tm_year > 100) {
    int h = tm->tm_hour, m = tm->tm_min, s = tm->tm_sec;
    bool night = (h >= 22 || h < 6);
    ring.setBrightness(night ? 8 : 60);          // dim at night
    ring.clear();
    ring.setPixelColor((h % 12) * 5 + m / 12, ring.Color(255, 0, 0));     // hour hand, red
    ring.setPixelColor(m, ring.Color(0, 255, 0));                          // minute hand, green
    uint32_t cs = ring.Color(0, 0, 120);
    ring.setPixelColor(s, cs);                                             // second dot, blue
    ring.setPixelColor((s + 59) % 60, ring.Color(0, 0, 30));               // short tail
    ring.show();
  }
  delay(100);
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Hands in the right placeMatch the phone time
Second dotMoves once a second
At 22:00Ring dims
Tunnel effectSeveral reflections look like an endless depth

If it does not work

Time off by hours

Change the offset in configTime.

No tunnel

Check the mirror spacing and that the front is a two-way mirror.

Colours wrong

Try NEO_RGB.

Flicker

Check the ground and the capacitor.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the infinity mirror clock?

ESP32 DevKit V1, WS2812B strip 5 m (30 LEDs/m), 5 V 2 A USB adapter, Resistor 330 Ω and Electrolytic capacitor 1000 µF. WS2812B strip 5 m (30 LEDs/m): Cut 60 LEDs.

How long does the infinity mirror clock take to build?

About 240 minutes for a intermediate maker, in 8 steps.

How do I know the infinity mirror clock works?

Hands in the right place: Match the phone time. Second dot: Moves once a second. At 22:00: Ring dims.

Time off by hours: what should I check?

Change the offset in configTime.

No tunnel: what should I check?

Check the mirror spacing and that the front is a two-way mirror.

Colours wrong: what should I check?

Try NEO_RGB.

Flicker: what should I check?

Check the ground and the capacitor.