Projects / DIY power bank with charge display

DIY power bank with charge display

Beginner1.5 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. 3.52 V

    Match the cells

    Measure each cell with a multimeter. They must be within 0.1 V of each other before you connect them in parallel.

  2. +

    Check the module

    Read the board's labels so B+, B-, OUT and IN are correct. Look for the protection chip.

  3. +

    Join the cells

    Put both cells in a two-cell holder wired in parallel, then to the module's B+ and B-.

  4. ++

    Add the level indicator

    Connect it to the same B+ and B-.

  5. 3.53 V

    Test the output

    Measure 5 V at the USB socket with a multimeter, then plug in a phone.

  6. ++ABS

    Fit the box

    Mount everything so nothing can short, with holes for USB and the indicator.

  7. +

    Charge it

    Plug in a charger and watch the module's charge light.

In short

How do you build a DIY power bank with charge display?

Two protected 18650 cells in parallel feed a ready charge-and-boost module and a level indicator, making a 5 V USB power bank. You need Li-ion 3.7 V 18650 with protection (button top) × 2, 18650 battery charger and boost (5 V / 1 A), Lithium battery level indicator (1S to 4S), ABS project box (100 × 60 × 25 mm) and Digital multimeter. It takes 7 steps and about 90 minutes.

Level
Beginner
Time
About 90 min
Parts
5

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Cell 1 + and Cell 2 +Module B+ (joined)Cells in parallel
Cell 1 - and Cell 2 -Module B- (joined)Cells in parallel
Module USB outputUSB cable to the phone5 V at up to 1 A
Module micro-USB or USB-C inputChargerCharges the pack
Level indicator B+ and B-Pack + and -Shows cell voltage as bars

No code needed

No code. Match the two cells at the same voltage within 0.1 V before joining them, and always use the same make, model and age. Never short the cells, never use damaged cells, and never leave a charging pack unattended. Use a module with protection and a 1 A rating as listed.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Output voltage5.0 V plus or minus 0.2 V
Load a phoneCharges at about 1 A and the module stays only warm
Level indicatorShows bars matching a multimeter reading of the cells
ChargeCharge light shows red then changes to full

If it does not work

No output

Check B+ and B- polarity and that the module's input is set up for its cell count.

Pack gets hot

Stop at once. Check the cells, polarity and load.

Level reads wrong

The indicator is for a different cell count. Match it to 1S.

Only one cell charges

The cells were at very different voltages. Recheck and balance them separately first.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the DIY power bank with charge display?

Li-ion 3.7 V 18650 with protection (button top) × 2, 18650 battery charger and boost (5 V / 1 A), Lithium battery level indicator (1S to 4S), ABS project box (100 × 60 × 25 mm) and Digital multimeter.

How long does the DIY power bank with charge display take to build?

About 90 minutes for a beginner maker, in 7 steps.

How do I know the DIY power bank with charge display works?

Output voltage: 5.0 V plus or minus 0.2 V. Load a phone: Charges at about 1 A and the module stays only warm. Level indicator: Shows bars matching a multimeter reading of the cells.

No output: what should I check?

Check B+ and B- polarity and that the module's input is set up for its cell count.

Pack gets hot: what should I check?

Stop at once. Check the cells, polarity and load.

Level reads wrong: what should I check?

The indicator is for a different cell count. Match it to 1S.

Only one cell charges: what should I check?

The cells were at very different voltages. Recheck and balance them separately first.