Build it step by step
0 of 8 doneJoin the wiper
Wire the wiper to terminal 3.
Wire the circuit
5 V, pot, 220 ohm, meter, LED, ground.
Set the pot
Start at its lowest resistance.
Measure the current
Meter in series on the mA range.
Turn in five steps
Note current and brightness.
Plot the graph
Current against position.
Compare
Check against the calculated values.
Restore the leads
Red lead back to the voltage jack.
How do you build a rheostat LED dimmer?
A 1 kilohm pot used as a variable resistor dims an LED from a 5 V supply, and you plot current against pot position. You need Potentiometer 1 kΩ (linear), LED 5 mm white, Resistor 220 Ω, 5 V 2 A USB adapter, Digital multimeter, Jumper wires male to male (40 pcs, 20 cm) and Breadboard 830 Tie Points. It takes 8 steps and about 60 minutes.
- Level
- Beginner
- Time
- About 60 min
- Parts
- 7
Parts list
- PassivesBuy
- OptoelectronicsBuyLED 5 mm white × 1
- PassivesBuyResistor 220 Ω × 1
- PowerBuy
- Tools & InstrumentsBuy
- PrototypingBuy
- PrototypingBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| 5 V adapter positive | Pot terminal 1 | Start of the rheostat |
| Pot wiper (middle) | Pot terminal 3 (joined) | Wiper tied to one end so the pot is a two-wire resistor |
| Pot terminal 3 and wiper | 220 ohm resistor | Fixed minimum resistance |
| 220 ohm resistor | Multimeter (mA range) red probe | Measures the LED current |
| Multimeter black probe | White LED anode (long leg) | Current flows through the meter |
| LED cathode (short leg) | 5 V adapter negative | Common ground |
Code
A potentiometer has three terminals, but if you join the wiper to one end, the part becomes a simple variable resistor, called a rheostat, between the other end and the wiper. Put it in series with an LED and a fixed resistor and you have a dimmer: as the pot resistance rises, the current falls and the LED gets dimmer. The fixed 220 ohm resistor matters because the pot can be turned to zero ohms, and without a resistor the LED would then see the whole supply and burn out. Measure the current with the meter in series on its milliamp range, record it at five pot positions, and compare with the calculation: current is the supply minus the LED voltage divided by the total resistance. The graph is not a straight line. Current changes quickly over the first part of the pot and slowly over the rest, because it follows one divided by resistance. The same circuit is a good example of why a rheostat dimmer wastes power: the resistor and pot turn the rest of the supply into heat, which is fine for 10 milliamps and a poor design for a lamp. For larger loads, designers switch the current on and off quickly with PWM, which wastes almost nothing. Remember to return the red lead to the voltage jack after every current measurement.
Build notes (no code needed for this build) A rheostat is a variable resistor with two connections. A three-terminal pot becomes one when the wiper is joined to one end. Always keep a fixed resistor in series (here 220 ohm) so the current stays safe when the pot is at zero ohms. Calculated current, taking a white LED forward voltage of about 3.0 V and a 5.0 V supply: I = (5.0 - 3.0) / (220 + R) pot at 0 percent (R = 0 ohm) : about 9 mA pot at 25 percent (R = 250 ohm) : about 4.3 mA pot at 50 percent (R = 500 ohm) : about 2.8 mA pot at 75 percent (R = 750 ohm) : about 2.1 mA pot at 100 percent (R = 1000 ohm): about 1.6 mA The real LED voltage falls a little at low current, so real currents at the dim end are a little higher. Method: 1. Put the meter in series on the mA range, red lead in the mA jack. 2. Set the pot to the stop where its resistance is lowest, then turn in five steps. 3. Record the current and note the brightness from one to five. 4. Plot current against position: it is not a straight line, because current goes as one divided by resistance. 5. Move the red lead back to the voltage jack when you finish. Brightness is roughly proportional to current, but your eye sees changes at low light more than at high light, so the dim end looks easier to control.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Pot at its lowest resistance | Brightest, about 8 to 9 mA |
| Pot half way | About 3 mA |
| Pot at its highest | Dim, about 1.5 to 2 mA |
| Graph shape | A curve, steep at first |
| Meter reads zero | Check the fuse and the lead in the mA jack |
If it does not work
LED does not light
Check the LED direction and the supply.
Current jumps while turning
The wiper contact is dirty, turn it back and forth.
Meter reads zero
Check the red lead is in the mA jack.
LED flashes at the pot ends
The wiper is not joined to terminal 3.
LED very bright at one end
Check the 220 ohm resistor is still in series.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the rheostat LED dimmer?
Potentiometer 1 kΩ (linear), LED 5 mm white, Resistor 220 Ω, 5 V 2 A USB adapter, Digital multimeter, Jumper wires male to male (40 pcs, 20 cm) and Breadboard 830 Tie Points.
How long does the rheostat LED dimmer take to build?
About 60 minutes for a beginner maker, in 8 steps.
How do I know the rheostat LED dimmer works?
Pot at its lowest resistance: Brightest, about 8 to 9 mA. Pot half way: About 3 mA. Pot at its highest: Dim, about 1.5 to 2 mA.
LED does not light: what should I check?
Check the LED direction and the supply.
Current jumps while turning: what should I check?
The wiper contact is dirty, turn it back and forth.
Meter reads zero: what should I check?
Check the red lead is in the mA jack.
LED flashes at the pot ends: what should I check?
The wiper is not joined to terminal 3.
