Projects / Plant grow shelf timer

Plant grow shelf timer

Beginner1.5 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. NANODS323115:17

    Test the RTC

    Print the time and set it.

  2. NANOON

    Test the relays

    Click each channel from code.

  3. NANO12

    Wire the 12 V side

    Fit a fuse on the adapter lead.

  4. NANO

    Add the schedule

    Lights on in the daytime hours.

  5. NANO

    Add the fan cycle

    5 minutes each hour.

  6. NANO

    Add the override

    Press to force the lights on.

  7. NANO

    Run for a week

    Check the time drift and the plants.

In short

How do you build a plant grow shelf timer?

A timer for a shelf of plants that runs lights 14 hours and a fan for 5 minutes each hour. You need Arduino Nano, DS3231 RTC module, Relay module 2-channel 5 V, 12 V DC fan 80 mm, 12 V LED strip warm white (5 m, 2835), 12 V 2 A DC adapter and Tactile push button 6 mm. It takes 7 steps and about 90 minutes.

Level
Beginner
Time
About 90 min
Parts
7

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
DS3231 VCC, GNDNano 5V, GNDPower
DS3231 SDA, SCLNano A4, A5I2C
Relay module VCC, GNDNano 5V, GNDPower
Relay IN1Nano D4Light channel
Relay IN2Nano D5Fan channel
12 V adapter plusRelay 1 COM and relay 2 COMCommon supply
Relay 1 NOLED strip + (strip − to adapter −)Lights
Relay 2 NOFan + (fan − to adapter −)Fan
ButtonNano D2 and GNDManual override
Nano5 V from a USB adapterPower (separate from the 12 V loads)

Code

The DS3231 keeps time through power cuts with its coin cell, so the schedule survives a blackout. Edit the hours at the top to suit your plants; seedlings often need 14 to 16 hours of light, but different plants differ, so check what yours need. The relay module switches only the 12 V side here: the 12 V adapter powers the strip and fan, and the Nano has its own 5 V supply. Never wire mains to the relay in this build; if you want to switch a mains grow light, a qualified electrician must wire the mains side with a suitably rated, enclosed relay unit. Use a fuse on the 12 V lead and keep the electronics away from water. Arduino IDE, board "Arduino Nano" (try the Old Bootloader option if the upload fails).

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// Plant shelf timer: lights 06:00 to 20:00, fan 5 minutes each hour. Libraries: RTClib. Board: Arduino Nano.
#include <Wire.h>
#include <RTClib.h>

RTC_DS3231 rtc;
const int LIGHT = 4, FAN = 5, BTN = 2;
const int LIGHT_ON_HOUR = 6, LIGHT_OFF_HOUR = 20;       // 14 hours of light
const int FAN_MINUTES = 5;
bool override_on = false;
unsigned long lastBtn = 0;

void setup() {
  pinMode(LIGHT, OUTPUT); pinMode(FAN, OUTPUT); pinMode(BTN, INPUT_PULLUP);
  digitalWrite(LIGHT, HIGH); digitalWrite(FAN, HIGH);   // most relay boards are active LOW, HIGH = off
  Serial.begin(115200);
  if (!rtc.begin()) { Serial.println("RTC not found"); while (1); }
  if (rtc.lostPower()) rtc.adjust(DateTime(F(__DATE__), F(__TIME__)));   // set once from the compile time
}

void loop() {
  DateTime now = rtc.now();
  if (!digitalRead(BTN) && millis() - lastBtn > 400) { override_on = !override_on; lastBtn = millis(); }

  bool lightsOn = (now.hour() >= LIGHT_ON_HOUR && now.hour() < LIGHT_OFF_HOUR) || override_on;
  bool fanOn = (now.minute() < FAN_MINUTES);              // first 5 minutes of every hour
  digitalWrite(LIGHT, lightsOn ? LOW : HIGH);
  digitalWrite(FAN, fanOn ? LOW : HIGH);

  Serial.print(now.hour()); Serial.print(":"); Serial.print(now.minute());
  Serial.print(" lights "); Serial.print(lightsOn); Serial.print(" fan "); Serial.println(fanOn);
  delay(1000);
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual Arduino Nano with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

RTC not found

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
At 06:00Lights switch on
At 20:00Lights switch off
Each hourFan runs for 5 minutes
Unplug and replugSchedule continues at the right time

If it does not work

Relays reversed

Change active LOW to HIGH for your board.

Time resets to the compile time

Replace the RTC coin cell.

Fan never runs

Check the wiring to NO, not NC.

Nano resets when the lights switch

Use separate supplies and add a 100 µF capacitor.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the plant grow shelf timer?

Arduino Nano, DS3231 RTC module, Relay module 2-channel 5 V, 12 V DC fan 80 mm, 12 V LED strip warm white (5 m, 2835), 12 V 2 A DC adapter and Tactile push button 6 mm.

How long does the plant grow shelf timer take to build?

About 90 minutes for a beginner maker, in 7 steps.

How do I know the plant grow shelf timer works?

At 06:00: Lights switch on. At 20:00: Lights switch off. Each hour: Fan runs for 5 minutes.

Relays reversed: what should I check?

Change active LOW to HIGH for your board.

Time resets to the compile time: what should I check?

Replace the RTC coin cell.

Fan never runs: what should I check?

Check the wiring to NO, not NC.

Nano resets when the lights switch: what should I check?

Use separate supplies and add a 100 µF capacitor.