Projects / Pico touch dimmer lamp

Pico touch dimmer lamp

Beginner1.8 hGuided buildReviewed

Build it step by step

0 of 6 done
  1. PICOTTP223

    Wire the touch module

    VCC to 3V3(OUT), GND to GND, I/O to GP15.

  2. PICO12.0 mA

    Wire the LED

    Long leg through 330 ohms to GP16, short leg to GND.

  3. PICO12.0 mA

    Run the program

    The LED is off.

  4. PICO12.1 mA

    Tap the pad

    The LED fades to dim.

  5. PICO

    Tap again

    Medium, then bright, then off.

  6. PICO

    Save as main.py

    So it runs when you plug in the Pico.

In short

How do you build a pico touch dimmer lamp?

A Pico reads a TTP223 touch pad and cycles an LED lamp through off, dim, medium and bright with each tap, using PWM and a smooth fade. You need Raspberry Pi Pico H, Touch sensor module (TTP223), LED 5 mm red, Resistor 330 Ω and Breadboard 830 Tie Points. It takes 6 steps and about 110 minutes.

Level
Beginner
Time
About 110 min
Parts
5

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
TTP223 VCCPico 3V3(OUT) pin 36Power at 3.3 V
TTP223 GNDPico GND pin 38Common ground
TTP223 I/OPico GP15 pin 20High while touched
LED long leg330 ohm resistor to Pico GP16 pin 21Dimmed by PWM
LED short legPico GND pin 23Ground

Code

The TTP223 is a touch switch chip. A metal pad on the board forms one plate of a tiny capacitor with your finger as the other plate, and the chip notices the small change and sets its output pin high. Because it measures capacitance there are no moving parts. The Pico watches for the moment the output goes from low to high, which is a new touch, and steps to the next brightness level. To make the LED seem to change smoothly the program does not jump to the new level but moves toward it a little each ten milliseconds, so a change takes about a quarter of a second. The LED is driven by PWM, which switches it on and off a thousand times a second with a changing share of on time. The four levels are spaced unevenly on purpose, because our eyes judge brightness on a curve, so equal steps would look as if the lowest levels did nearly nothing.

import time
from machine import Pin, PWM

touch = Pin(15, Pin.IN)
led = PWM(Pin(16))
led.freq(1000)

LEVELS = [0, 4096, 16384, 65535]                    # off, dim, medium, bright (spaced for the eye)
index = 0
current = 0
prev = 0

while True:
    t = touch.value()
    if t == 1 and prev == 0:                        # a new touch
        index = (index + 1) % len(LEVELS)
        time.sleep_ms(40)
    prev = t

    target = LEVELS[index]
    if current < target:
        current = min(target, current + 2500)       # fade up
    elif current > target:
        current = max(target, current - 2500)       # fade down
    led.duty_u16(current)
    time.sleep_ms(10)

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
StartLED off
First tapFades to dim
Second tapMedium
Third tapBright
Fourth tapFades off

If it does not work

LED does not light

Check the LED direction, the long leg goes to the resistor.

Skips levels

A tap is read twice, raise the 40 millisecond pause.

Changes by itself

Keep your hand and wires away from the pad, and keep the module on a stable surface.

Brightness steps look uneven

Change the numbers in the LEVELS list.

Pad does nothing

Check the I/O wire is on GP15 and the module has 3.3 V.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the pico touch dimmer lamp?

Raspberry Pi Pico H, Touch sensor module (TTP223), LED 5 mm red, Resistor 330 Ω and Breadboard 830 Tie Points.

How long does the pico touch dimmer lamp take to build?

About 110 minutes for a beginner maker, in 6 steps.

How do I know the pico touch dimmer lamp works?

Start: LED off. First tap: Fades to dim. Second tap: Medium.

LED does not light: what should I check?

Check the LED direction, the long leg goes to the resistor.

Skips levels: what should I check?

A tap is read twice, raise the 40 millisecond pause.

Changes by itself: what should I check?

Keep your hand and wires away from the pad, and keep the module on a stable surface.

Brightness steps look uneven: what should I check?

Change the numbers in the LEVELS list.