Projects / Pico dusk night light

Pico dusk night light

Intermediate2 hGuided buildReviewed

Build it step by step

0 of 6 done
  1. PICO146 lux

    Build the divider

    Photoresistor from 3V3(OUT) to GP27, 10 kilo-ohm from GP27 to GND.

  2. PICO8.4 mA

    Wire the LED

    GP15 through 330 ohms, cathode to GND.

  3. PICO

    Switch the room light on

    Then run the program.

  4. PICO8.4 mA

    Cover the sensor with your hand

    The LED fades up.

  5. PICO8.4 mA

    Uncover it

    The LED fades out.

  6. PICO

    Try a small change in light

    No flicker.

In short

How do you build a pico dusk night light?

A Pico switches an LED on at dusk using a photoresistor and fades it up and down with PWM, with no knob needed. You need Raspberry Pi Pico H, LDR Photoresistor, Resistor 10 kΩ, LED 5 mm red, Resistor 330 Ω and Breadboard 830 Tie Points. It takes 6 steps and about 120 minutes.

Level
Intermediate
Time
About 120 min
Parts
6

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Photoresistor one legPico 3V3(OUT) pin 36Top of the divider
Photoresistor other leg and 10 kilo-ohm resistorPico GP27 pin 32 (ADC1)Divider output
10 kilo-ohm resistor other legPico GNDBottom of the divider
LED anode330 ohm resistor to Pico GP15 pin 20Night light
LED cathodePico GNDReturn

Code

A photoresistor changes its resistance with light, and in series with a fixed resistor it forms a divider whose output voltage rises as the light gets brighter. The ADC turns the voltage into a number. The program takes the light level at start-up as a reference, so switch the room light on first, and decides it is getting dark when the reading falls below half of that. It switches back off only when the light rises above 65 percent of the reference. The gap between the two limits is called hysteresis, and it stops the LED flickering when the light sits right at the threshold. The LED is not switched on and off sharply: a PWM signal changes its brightness a little each cycle, which gives a smooth fade. Low voltage only, and the 330 ohm resistor protects the LED and the pin.

import time
from machine import ADC, Pin, PWM

ldr = ADC(27)
led = PWM(Pin(15))
led.freq(1000)

def read_light():
    total = 0
    for _ in range(8):
        total += ldr.read_u16()
    return total // 8

# Set the reference from the room light at start-up (switch the room light on first)
time.sleep(1)
reference = read_light()
ON_BELOW = reference * 5 // 10                   # go dark below half the start-up light
OFF_ABOVE = reference * 65 // 100                # come back on above 65 percent: hysteresis

target = 0
duty = 0
while True:
    light = read_light()
    if light < ON_BELOW:
        target = 30000                           # about half brightness
    elif light > OFF_ABOVE:
        target = 0
    if duty < target:
        duty = min(duty + 300, target)           # fade up
    elif duty > target:
        duty = max(duty - 300, target)           # fade down
    led.duty_u16(duty)
    time.sleep_ms(20)

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Room light onLED off
Sensor coveredLED fades on
Sensor uncoveredLED fades off
Light near the thresholdNo flicker
Restart in a dim roomReference is lower, so it needs darker to switch

If it does not work

LED never lights

Check polarity, GP15 and the resistor.

LED always on

Run it with the room light on, or swap the divider parts.

Flickers

Widen the gap between ON_BELOW and OFF_ABOVE.

No reaction to light

Check the divider wiper goes to GP27.

Program does not start on power-up

Save it on the Pico as main.py.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the pico dusk night light?

Raspberry Pi Pico H, LDR Photoresistor, Resistor 10 kΩ, LED 5 mm red, Resistor 330 Ω and Breadboard 830 Tie Points.

How long does the pico dusk night light take to build?

About 120 minutes for a intermediate maker, in 6 steps.

How do I know the pico dusk night light works?

Room light on: LED off. Sensor covered: LED fades on. Sensor uncovered: LED fades off.

LED never lights: what should I check?

Check polarity, GP15 and the resistor.

LED always on: what should I check?

Run it with the room light on, or swap the divider parts.

Flickers: what should I check?

Widen the gap between ON_BELOW and OFF_ABOVE.

No reaction to light: what should I check?

Check the divider wiper goes to GP27.