Projects / Pet water bowl reminder

Pet water bowl reminder

Beginner50 minGuided buildReviewed

Build it step by step

0 of 7 done
  1. NANO

    Stick the sensor on the bowl

    At the low mark on a flat wall, on the outside.

  2. NANO

    Wire the sensor

    5V, GND and OUT to D2.

  3. NANO17.4 mA

    Wire the light, buzzer and button

    LED through 220 ohms to D6, buzzer to D8, button to D3.

  4. NANO

    Upload and check the serial monitor

    It says the bowl watch started.

  5. NANOY25

    Pour water above the mark

    Nothing happens.

  6. NANOY25

    Lower the water below the mark

    After ten seconds the light flashes.

  7. NANO

    Press the button

    The light stops until you refill.

In short

How do you build a pet water bowl reminder?

A non-contact sensor stuck to the outside of a pet's water bowl flashes a light when the water is low and beeps once if it stays low for an hour. It does not replace checking the bowl. Keep the electronics beside the bowl and away from splashes. You need Arduino Nano, Water level sensor (non-contact, XKC-Y25), LED 5 mm red, Resistor 220 Ω, Passive buzzer, Tactile push button 6 mm, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 7 steps and about 50 minutes.

Level
Beginner
Time
About 50 min
Parts
8

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Sensor VCC and GNDNano 5V and GNDSensor power
Sensor OUTNano D2High or low depending on the water
LED long legNano D6 through a 220 ohm resistor, short leg to GNDLow water light
Passive buzzer + and -Nano D8 and GNDOne reminder beep
Silence buttonNano D3 and GNDSilences the light and beep until you refill

Code

The non-contact sensor sticks to the outside of the bowl and senses whether there is water on the other side of the wall, so nothing gets wet. Put it at the level you call low. Many of these modules give a high signal when they sense water and a low signal when they do not, and some give the opposite, so if the light does the wrong thing change WET_IS_HIGH. The sensor works through thin plastic or glass, and works best on a flat wall, so check it with the bowl full and with the water below the mark. A low reading must last ten seconds before it counts, so a pet knocking the bowl or the water sloshing does not set it off. When the water is low the light flashes, and if it is still low after an hour the buzzer gives a single beep. The silence button stops the light until the sensor sees water again. This is a reminder only and never a substitute for looking at the bowl every day, especially in hot weather. Keep the Nano, buzzer and wiring out of reach of pets and away from splashes, and keep wires tidy so they cannot be chewed.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

const uint8_t SENSOR = 2;
const uint8_t BTN = 3;
const uint8_t LED = 6;
const uint8_t BUZZ = 8;

const bool WET_IS_HIGH = true;                  // change if your module gives the opposite
const unsigned long LOW_CONFIRM_MS = 10000UL;    // water must read low this long (stops sloshing false alarms)
const unsigned long BEEP_AFTER_MS = 3600000UL;   // one beep after an hour

bool lowWater = false;
bool silenced = false;
bool beeped = false;
unsigned long lowSince = 0;
unsigned long lowCandidateSince = 0;
bool candidate = false;

bool isWet() {
  bool level = digitalRead(SENSOR);
  return WET_IS_HIGH ? level : !level;
}

void setup() {
  pinMode(SENSOR, INPUT);
  pinMode(BTN, INPUT_PULLUP);
  pinMode(LED, OUTPUT);
  pinMode(BUZZ, OUTPUT);
  Serial.begin(9600);
  Serial.println(F("Bowl watch started."));
}

void loop() {
  unsigned long now = millis();
  bool wet = isWet();

  if (wet) {                                    // refilled: clear everything
    if (lowWater) Serial.println(F("Water is back."));
    lowWater = false; candidate = false; silenced = false; beeped = false;
    digitalWrite(LED, LOW);
  } else {
    if (!candidate) { candidate = true; lowCandidateSince = now; }
    if (!lowWater && now - lowCandidateSince >= LOW_CONFIRM_MS) {
      lowWater = true;
      lowSince = now;
      Serial.println(F("Water is low."));
    }
  }

  if (lowWater && !silenced) {
    digitalWrite(LED, (now / 500) % 2);         // flash the light
    if (!beeped && now - lowSince >= BEEP_AFTER_MS) {
      tone(BUZZ, 1500, 400);                    // one reminder beep, not a continuous alarm
      beeped = true;
    }
  } else if (lowWater) {
    digitalWrite(LED, LOW);
  }

  if (digitalRead(BTN) == LOW) { silenced = true; delay(200); }
  delay(50);
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual Arduino Nano with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

Bowl watch started.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Water above the markLight off
Water below for ten secondsLight flashes
Low for an hourOne beep
Silence buttonLight stops
RefillEverything resets

If it does not work

Light flashes with a full bowl

Change WET_IS_HIGH to false.

Never notices the water level

Press the sensor flat against the wall and move it to the mark.

False alarms

Increase LOW_CONFIRM_MS.

No beep

Wait a full hour, or shorten BEEP_AFTER_MS to test.

LED stays dark

Check its direction and the 220 ohm resistor.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the pet water bowl reminder?

Arduino Nano, Water level sensor (non-contact, XKC-Y25), LED 5 mm red, Resistor 220 Ω, Passive buzzer, Tactile push button 6 mm, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).

How long does the pet water bowl reminder take to build?

About 50 minutes for a beginner maker, in 7 steps.

How do I know the pet water bowl reminder works?

Water above the mark: Light off. Water below for ten seconds: Light flashes. Low for an hour: One beep.

Light flashes with a full bowl: what should I check?

Change WET_IS_HIGH to false.

Never notices the water level: what should I check?

Press the sensor flat against the wall and move it to the mark.

False alarms: what should I check?

Increase LOW_CONFIRM_MS.

No beep: what should I check?

Wait a full hour, or shorten BEEP_AFTER_MS to test.