Overvoltage crowbar protection
Build it step by step
0 of 7 doneDraw the circuit
Zener, SCR, fuse.
Build it on a breadboard
No load yet.
Raise the supply slowly
From 0 V up to 7 V.
Note when the SCR fires
Voltage and current.
Add the load
A LED and resistor.
Test again
With a current limit.
Reset the fuse
Let it cool and retest.
How do you build an overvoltage crowbar protection?
A Zener diode and an SCR short the supply and blow a fuse if it ever goes above a safe voltage, protecting expensive boards. You need TYN612 SCR, Zener diode 5.1 V (1N4733A), Resistor 1 kΩ, Ceramic Capacitor 100 nF, Polyfuse (PTC resettable) 500 mA and Digital multimeter. It takes 7 steps and about 90 minutes.
- Level
- Intermediate
- Time
- About 90 min
- Parts
- 6
Parts list
- SemiconductorsBuyTYN612 SCR × 1
- SemiconductorsBuy
- PassivesBuyResistor 1 kΩ × 1
- PassivesBuy
- Passives
- Tools & InstrumentsBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| Supply plus | Polyfuse, then the protected rail | Fuse in series |
| Protected rail | SCR anode (middle pin, front view) | Crowbar path |
| SCR cathode (left pin) | Supply minus | Short to ground when fired |
| Zener cathode (stripe) | Protected rail | Senses the voltage |
| Zener anode | SCR gate (right pin) | Trigger |
| 1 k resistor | SCR gate to ground | Keeps the gate quiet |
| 100 nF capacitor | SCR gate to ground | Stops false triggers from noise |
| Load | Connected to the protected rail and ground | The board being protected |
No code needed
A crowbar is the electronics version of dropping a crowbar across the supply: if the voltage ever rises above a safe level, a switch shorts it out so hard that a fuse blows before the board can be harmed. Here a 5.1 V Zener does the sensing, and when the rail goes about 0.7 V above that, enough gate current flows to fire the SCR, which then conducts like a short until the power is removed. The resettable fuse in series opens under the short. Two cautions. First, the SCR needs a certain gate current to fire, so the real trigger voltage may be a little higher than the sum; test it with a variable supply rising slowly, and try a slightly larger Zener if it does not fire. Second, the crowbar works only if the supply and fuse can trip quickly under a short, so it suits a small supply, not a powerful one. Test with a current-limited bench supply first, never with a board you care about, and keep the circuit off mains wiring. There is no code for this build.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Supply 5.0 V | Rail stays up, nothing fires |
| Supply above about 6 V | SCR fires, fuse trips |
| After the fuse cools | Circuit works again |
| Gate capacitor | No false firing on switching |
If it does not work
Never fires
Use a smaller gate resistor or a slightly larger Zener.
Fires at normal voltage
Check the Zener value and polarity.
Fuse never trips
The supply is too weak; raise its current limit.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the overvoltage crowbar protection?
TYN612 SCR, Zener diode 5.1 V (1N4733A), Resistor 1 kΩ, Ceramic Capacitor 100 nF, Polyfuse (PTC resettable) 500 mA and Digital multimeter.
How long does the overvoltage crowbar protection take to build?
About 90 minutes for a intermediate maker, in 7 steps.
How do I know the overvoltage crowbar protection works?
Supply 5.0 V: Rail stays up, nothing fires. Supply above about 6 V: SCR fires, fuse trips. After the fuse cools: Circuit works again.
Never fires: what should I check?
Use a smaller gate resistor or a slightly larger Zener.
Fires at normal voltage: what should I check?
Check the Zener value and polarity.
Fuse never trips: what should I check?
The supply is too weak; raise its current limit.
