Op-amp inverting amplifier lab
Build it step by step
0 of 7 doneMake the split supply
Join the + of one battery to the − of the other. That joint is ground, the free ends are +9 V and −9 V.
Wire the chip
Pin 8 to +9 V, pin 4 to −9 V, 100 nF from each to ground. Park the unused amplifier.
Build the amplifier
Rin 10 kΩ into pin 2, Rf 100 kΩ from pin 1 to pin 2, pin 3 to ground.
Set the input
Use the pot between the rails and measure its wiper with the meter. Keep it small, about ±0.3 V.
Measure the output
The output is about −10 times the input.
Swap the feedback resistor
Use 22 kΩ and see the gain fall to −2.2.
Find the clipping
Raise the input and see where the output stops following.
How do you build an op-amp inverting amplifier lab?
Build an inverting amplifier with an LM358 and measure how gain follows the resistor ratio. You need LM358 Op-Amp, Resistor 10 kΩ × 2, Resistor 100 kΩ, Resistor 22 kΩ, Ceramic Capacitor 100 nF × 2, Potentiometer 10 kΩ, Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm), 9 V battery × 2, 9 V battery snap with DC jack × 2 and Digital multimeter. It takes 7 steps and about 60 minutes.
- Level
- Beginner
- Time
- About 60 min
- Parts
- 11
Parts list
- Integrated CircuitsBuyLM358 Op-Amp × 1
- PassivesBuyResistor 10 kΩ × 2
- PassivesBuyResistor 100 kΩ × 1
- PassivesBuyResistor 22 kΩ × 1
- PassivesBuy
- PassivesBuy
- PrototypingBuy
- PrototypingBuy
- BatteriesBuy9 V battery × 2
- PowerBuy
- Tools & InstrumentsBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| Two 9 V batteries in series | Middle joint is 0 V (ground) | Gives +9 V and −9 V |
| LM358 pin 8 | +9 V | Positive supply |
| LM358 pin 4 | −9 V | Negative supply |
| 100 nF | Pin 8 to ground, and pin 4 to ground | Decoupling |
| Pot ends | +9 V and −9 V | Test input |
| Pot wiper | 10 kΩ (Rin) then pin 2 (IN−) | Input resistor |
| Pin 3 (IN+) | Ground | Reference |
| Pin 1 (OUT) | 100 kΩ (Rf) to pin 2 | Feedback |
| Unused amplifier (pins 5, 6, 7) | Pin 5 to ground, pin 6 to pin 7 | Parked |
No code needed
No code. Gain = −Rf ÷ Rin, so 100 kΩ over 10 kΩ gives −10. With 22 kΩ it gives −2.2. The LM358 output cannot reach the supply rails, so it clips about 1.5 V below the positive rail but near the negative one. With two 9 V batteries, expect clipping around +7 V.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Vin +0.3 V, Rf 100 kΩ | Vout near −3 V |
| Vin −0.3 V | Vout near +3 V |
| Rf 22 kΩ | Gain about −2.2 |
| Large input | Output clips near +7 V and near −8 V |
If it does not work
Output stuck at a rail
The feedback is open or pin 3 is not grounded.
Gain is lower than predicted
Resistors are 5 % tolerance. Measure each one.
Output offset with zero input
Op-amp input offset. Small errors are normal.
Output oscillates
Add the 100 nF supply capacitors close to the chip and keep leads short.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the op-amp inverting amplifier lab?
LM358 Op-Amp, Resistor 10 kΩ × 2, Resistor 100 kΩ, Resistor 22 kΩ, Ceramic Capacitor 100 nF × 2, Potentiometer 10 kΩ, Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm), 9 V battery × 2, 9 V battery snap with DC jack × 2 and Digital multimeter.
How long does the op-amp inverting amplifier lab take to build?
About 60 minutes for a beginner maker, in 7 steps.
How do I know the op-amp inverting amplifier lab works?
Vin +0.3 V, Rf 100 kΩ: Vout near −3 V. Vin −0.3 V: Vout near +3 V. Rf 22 kΩ: Gain about −2.2.
Output stuck at a rail: what should I check?
The feedback is open or pin 3 is not grounded.
Gain is lower than predicted: what should I check?
Resistors are 5 % tolerance. Measure each one.
Output offset with zero input: what should I check?
Op-amp input offset. Small errors are normal.
Output oscillates: what should I check?
Add the 100 nF supply capacitors close to the chip and keep leads short.
