Projects / Nokia 5110 retro display games

Nokia 5110 retro display games

Beginner1.5 hGuided buildReviewed

Build it step by step

0 of 6 done
  1. NANO

    Wire the display

    Connect the 3V3, GND and five signal lines through 10 kΩ resistors.

  2. NANOHelloPCD8544

    Draw text

    Use the Adafruit PCD8544 "pcdtest" example and set the contrast.

  3. NANO

    Add the backlight

    Wire the backlight pin through 330 Ω and check which level turns it on.

  4. NANO

    Add buttons

    Wire the five buttons to the pins in the table.

  5. NANO

    Upload Snake

    Steer to the food dot and watch the snake grow.

  6. NANO

    Measure the current

    Put the meter in the 3V3 line to see the tiny draw with the backlight off.

In short

How do you build a nokia 5110 retro display games?

The old Nokia phone screen shows Snake and text with very low power, driven from a 5 V Nano. You need Arduino Nano, Nokia 5110 LCD (PCD8544), Tactile push button 6 mm × 5, Resistor 10 kΩ × 5, Resistor 330 Ω, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 6 steps and about 90 minutes.

Level
Beginner
Time
About 90 min
Parts
7

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
5110 VCCNano 3V3Display runs at 3.3 V
5110 GNDNano GNDGround
Nano D810 kΩ resistor then 5110 CLKClock (series resistor protects the 3.3 V input)
Nano D910 kΩ resistor then 5110 DINData
Nano D1010 kΩ resistor then 5110 DCData or command
Nano D1110 kΩ resistor then 5110 CEChip select
Nano D1210 kΩ resistor then 5110 RSTReset
Nano D3330 Ω resistor then 5110 BLBacklight (check your module, some are active low)
Up, down, left, right buttonsNano D4, D5, D6, D7 and GNDGame controls
Backlight buttonNano D2 and GNDToggles the backlight

Code

Arduino IDE, board "Arduino Nano" (processor ATmega328P, or ATmega328P (Old Bootloader) for clones). Install "Adafruit PCD8544 Nokia 5110 LCD library" and "Adafruit GFX Library". The display is a 3.3 V part, so it is powered from the Nano's 3V3 pin and its signal lines pass through 10 kΩ series resistors, a common low-cost arrangement that relies on the chip's input protection. For a fully rated design use a proper level shifter. Adjust setContrast (40 to 70) until the pixels look right.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <Adafruit_GFX.h>
#include <Adafruit_PCD8544.h>

Adafruit_PCD8544 lcd(8, 9, 10, 11, 12);       // CLK, DIN, DC, CE, RST
const byte UP = 4, DOWN = 5, LEFT = 6, RIGHT = 7, LIGHT = 2, BL = 3;
const byte W = 21, H = 12, CELL = 4;           // 84 x 48 pixels in 4-pixel cells
byte sx[60], sy[60];
byte len, dx, dy, fx, fy;
bool light = false;

void newFood() { fx = random(W); fy = random(H); }

void reset() {
  len = 3; dx = 1; dy = 0;
  for (byte i = 0; i < len; i++) { sx[i] = 10 - i; sy[i] = 6; }
  newFood();
}

void setup() {
  for (byte p = 4; p <= 7; p++) pinMode(p, INPUT_PULLUP);
  pinMode(LIGHT, INPUT_PULLUP);
  pinMode(BL, OUTPUT);
  lcd.begin();
  lcd.setContrast(55);
  randomSeed(analogRead(A0));
  reset();
}

void loop() {
  if (!digitalRead(LIGHT)) { light = !light; digitalWrite(BL, light); delay(250); }
  if (!digitalRead(UP) && dy == 0) { dx = 0; dy = -1; }
  if (!digitalRead(DOWN) && dy == 0) { dx = 0; dy = 1; }
  if (!digitalRead(LEFT) && dx == 0) { dx = -1; dy = 0; }
  if (!digitalRead(RIGHT) && dx == 0) { dx = 1; dy = 0; }

  for (byte i = len - 1; i > 0; i--) { sx[i] = sx[i - 1]; sy[i] = sy[i - 1]; }
  sx[0] += dx; sy[0] += dy;
  bool dead = sx[0] >= W || sy[0] >= H;          // unsigned wrap catches the left and top walls
  for (byte i = 1; i < len; i++) if (sx[i] == sx[0] && sy[i] == sy[0]) dead = true;
  if (dead) {
    lcd.clearDisplay(); lcd.setTextSize(1); lcd.setTextColor(BLACK);
    lcd.setCursor(10, 14); lcd.print("Game over");
    lcd.setCursor(10, 26); lcd.print("Score "); lcd.print(len - 3);
    lcd.display(); delay(2500); reset(); return;
  }
  if (sx[0] == fx && sy[0] == fy && len < 60) { sx[len] = sx[len - 1]; sy[len] = sy[len - 1]; len++; newFood(); }

  lcd.clearDisplay();
  lcd.fillRect(fx * CELL + 1, fy * CELL + 1, 2, 2, BLACK);
  for (byte i = 0; i < len; i++) lcd.fillRect(sx[i] * CELL, sy[i] * CELL, CELL - 1, CELL - 1, BLACK);
  lcd.display();
  delay(150);
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Power onSnake appears and moves right
Press buttonsSnake turns, but never straight back on itself
Eat the foodSnake grows by one and a new dot appears
Hit a wallGame over with the score

If it does not work

Blank screen

Raise or lower the contrast, and check RST and CE.

Garbled pixels

Check the order of CLK, DIN and DC.

Backlight never lights

Some modules are active low. Invert the BL write.

Snake does not turn

Check button wiring to ground and the pin numbers.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the nokia 5110 retro display games?

Arduino Nano, Nokia 5110 LCD (PCD8544), Tactile push button 6 mm × 5, Resistor 10 kΩ × 5, Resistor 330 Ω, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).

How long does the nokia 5110 retro display games take to build?

About 90 minutes for a beginner maker, in 6 steps.

How do I know the nokia 5110 retro display games works?

Power on: Snake appears and moves right. Press buttons: Snake turns, but never straight back on itself. Eat the food: Snake grows by one and a new dot appears.

Blank screen: what should I check?

Raise or lower the contrast, and check RST and CE.

Garbled pixels: what should I check?

Check the order of CLK, DIN and DC.

Backlight never lights: what should I check?

Some modules are active low. Invert the BL write.

Snake does not turn: what should I check?

Check button wiring to ground and the pin numbers.