Build it step by step
0 of 7 doneSet the meter
Turn the dial to the diode symbol.
Test a 1N4007
Red on the plain end, black on the striped end: about 0.5 to 0.7 V.
Reverse the probes
The meter shows OL.
Test the 1N4148 and the 1N5819
Note that the Schottky reads clearly lower.
Test the red and blue LEDs
Red reads about 2 V and glows, blue may read OL.
Hide the marks on one diode
Find its direction by testing and then check the stripe.
Write a table
Part, forward reading, reverse reading.
How do you build a multimeter diode test lab?
Use the diode test setting on a multimeter to find which way each diode and LED conducts and what voltage it reads, so you can check any unknown or doubtful part in seconds. You need Digital multimeter, Rectifier Diode 1N4007, Signal Diode 1N4148, Schottky Diode 1N5819, LED 5 mm red and LED 5 mm blue. It takes 7 steps and about 35 minutes.
- Level
- Beginner
- Time
- About 35 min
- Parts
- 6
Parts list
- Tools & InstrumentsBuy
- SemiconductorsBuy
- SemiconductorsBuy
- SemiconductorsBuy
- SemiconductorsBuyLED 5 mm red × 1
- OptoelectronicsBuyLED 5 mm blue × 1
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| Red probe (VΩ socket) | Diode end without the stripe (anode) | Forward test |
| Black probe (COM socket) | Diode striped end (cathode) | Forward test |
| Probes swapped | Red on the stripe, black on the other end | Reverse test |
| Meter dial | The diode symbol, often shared with the buzzer | Diode test mode |
No code needed
No code. In diode test mode the meter pushes a small current through the part and shows the voltage across it. A good silicon diode reads about 0.5 to 0.7 V one way and shows OL, meaning open, the other way. A Schottky diode reads lower, about 0.15 to 0.35 V. A red LED often reads about 1.6 to 2.0 V and glows faintly. A blue LED needs about 2.8 to 3.2 V, which some meters cannot supply, so it may show OL both ways or glow faintly, and that does not mean it is bad. Meters differ, so use the readings to compare parts and to find which way a part conducts, not as exact figures. Test parts out of the circuit and never test a part that is connected to a power source, and discharge any capacitor first.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| 1N4007 forward | About 0.5 to 0.7 V |
| 1N4007 reverse | OL |
| 1N5819 forward | About 0.15 to 0.35 V |
| Red LED forward | About 1.6 to 2.0 V with a faint glow |
| Shorted or open diode | Reads the same or OL both ways |
If it does not work
OL both ways
The part may be open, or an LED needs more voltage than the meter gives.
Reads zero both ways
The part is shorted or you are on the buzzer position, so check the dial.
Readings jump
Hold the probes steady on clean leads.
Meter shows nothing
Check the battery and the probe sockets.
LED does not glow
Some meters cannot light it, so try the other direction and a dim room.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the multimeter diode test lab?
Digital multimeter, Rectifier Diode 1N4007, Signal Diode 1N4148, Schottky Diode 1N5819, LED 5 mm red and LED 5 mm blue.
How long does the multimeter diode test lab take to build?
About 35 minutes for a beginner maker, in 7 steps.
How do I know the multimeter diode test lab works?
1N4007 forward: About 0.5 to 0.7 V. 1N4007 reverse: OL. 1N5819 forward: About 0.15 to 0.35 V.
OL both ways: what should I check?
The part may be open, or an LED needs more voltage than the meter gives.
Reads zero both ways: what should I check?
The part is shorted or you are on the buzzer position, so check the dial.
Readings jump: what should I check?
Hold the probes steady on clean leads.
Meter shows nothing: what should I check?
Check the battery and the probe sockets.
