Projects / Model drawbridge

Model drawbridge

Beginner1.3 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. NANO59°

    Fit a light card deck to the servo arm

    Tape it so it lies flat at 0 degrees.

  2. NANO59°13.1 mA

    Wire the servo, button, LEDs and buzzer

    D9, D2, D6, D7 and D8.

  3. NANO

    Upload and open the serial monitor at 9600

    It says Bridge down.

  4. NANO

    Press the button

    The road light goes red and the warning flashes with the bell.

  5. NANO

    Watch the deck rise

    Slowly to the up position.

  6. NANO

    Press again

    It warns, lowers, then the road light goes out.

  7. NANO

    Adjust UP_ANGLE

    For your deck.

In short

How do you build a model drawbridge?

A button lowers and raises a model drawbridge deck on a servo while warning lights flash and a bell sounds, and the road light stays red whenever the bridge is not fully down. A lovely first model for state machines. You need Arduino Nano, SG90 Micro Servo, Tactile push button 6 mm, LED 5 mm red × 2, Resistor 220 Ω × 2, Passive buzzer, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 7 steps and about 80 minutes.

Level
Beginner
Time
About 80 min
Parts
8

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Servo signal (orange)Nano D9Moves the deck
Servo red and brownNano 5V and GNDServo power, a light card deck only
Button leg 1Nano D2Raise or lower request
Button leg 2Nano GNDPressing joins D2 to ground
Warning LED long legNano D6 through a 220 ohm resistor, short leg to GNDFlashes while the deck moves
Road light LED long legNano D7 through a 220 ohm resistor, short leg to GNDRed while the bridge is not down
Passive buzzer + and -Nano D8 and GNDThe bell

Code

Real lifting bridges follow a careful order, and this model copies it. When you press the button the road light goes red first, then the warning light flashes and the bell rings for three seconds, and only then does the deck move, slowly, one degree at a time so it looks like a heavy bridge. The road light stays red the whole time the bridge is up, and goes out only after the deck is fully down and has settled. The sketch is a simple sequence of states, with the button deciding whether to raise or lower. Use a light card deck on the servo and keep fingers clear while it moves. The servo is powered from the Nano's 5 volts, so keep the deck light, or the Nano may reset. This is a toy model for learning, never a design for a real bridge. Try adding a second button as an emergency stop, or a sensor that stops the deck if something is in the way.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <Servo.h>

const uint8_t BUTTON_PIN = 2;
const uint8_t WARN_LED = 6;
const uint8_t ROAD_LED = 7;
const uint8_t BUZZER_PIN = 8;
const uint8_t SERVO_PIN = 9;

const int DOWN_ANGLE = 0;
const int UP_ANGLE = 80;

Servo deck;
int angle = DOWN_ANGLE;
bool bridgeUp = false;

void warn(unsigned long ms) {                    // flash and ring the bell for a while
  unsigned long start = millis();
  while (millis() - start < ms) {
    digitalWrite(WARN_LED, HIGH);
    tone(BUZZER_PIN, 1500, 120);
    delay(200);
    digitalWrite(WARN_LED, LOW);
    delay(200);
  }
}

void moveTo(int target) {                        // slow, one degree at a time
  while (angle != target) {
    angle += (target > angle) ? 1 : -1;
    deck.write(angle);
    digitalWrite(WARN_LED, (millis() / 200) % 2); // keep flashing while moving
    delay(25);
  }
  digitalWrite(WARN_LED, LOW);
}

void setup() {
  pinMode(BUTTON_PIN, INPUT_PULLUP);
  pinMode(WARN_LED, OUTPUT);
  pinMode(ROAD_LED, OUTPUT);
  pinMode(BUZZER_PIN, OUTPUT);
  deck.attach(SERVO_PIN);
  deck.write(DOWN_ANGLE);
  Serial.begin(9600);
  Serial.println("Bridge down. Press the button to raise it.");
}

void loop() {
  if (digitalRead(BUTTON_PIN) == LOW) {
    delay(30);
    while (digitalRead(BUTTON_PIN) == LOW) {}    // wait for release
    digitalWrite(ROAD_LED, HIGH);                // road goes red first
    warn(3000);
    if (!bridgeUp) {
      Serial.println("Raising...");
      moveTo(UP_ANGLE);
      bridgeUp = true;
      Serial.println("Bridge up. Press to lower.");
    } else {
      Serial.println("Lowering...");
      moveTo(DOWN_ANGLE);
      bridgeUp = false;
      delay(500);
      digitalWrite(ROAD_LED, LOW);               // road reopens only when it is fully down
      Serial.println("Bridge down.");
    }
  }
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual Arduino Nano with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

Bridge down. Press the button to raise it.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Button pressRoad red, warning and bell for three seconds
Deck movementSlow and smooth
Bridge upRoad light stays red
LoweringWarning again, then the road reopens
Serial monitorPrints each stage

If it does not work

Servo twitches or the Nano resets

The deck is too heavy, use a lighter one.

Deck goes the wrong way

Swap UP_ANGLE and DOWN_ANGLE.

No bell

Check you have a passive buzzer on D8.

LED stays dark

Check its direction and the 220 ohm resistor.

Nothing happens on a press

Check the button is wired to D2 and GND.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the model drawbridge?

Arduino Nano, SG90 Micro Servo, Tactile push button 6 mm, LED 5 mm red × 2, Resistor 220 Ω × 2, Passive buzzer, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).

How long does the model drawbridge take to build?

About 80 minutes for a beginner maker, in 7 steps.

How do I know the model drawbridge works?

Button press: Road red, warning and bell for three seconds. Deck movement: Slow and smooth. Bridge up: Road light stays red.

Servo twitches or the Nano resets: what should I check?

The deck is too heavy, use a lighter one.

Deck goes the wrong way: what should I check?

Swap UP_ANGLE and DOWN_ANGLE.

No bell: what should I check?

Check you have a passive buzzer on D8.

LED stays dark: what should I check?

Check its direction and the 220 ohm resistor.