Projects / Milk cooler temperature logger

Milk cooler temperature logger

Intermediate2.5 hGuided buildReviewed

Build it step by step

0 of 8 done
  1. UNODS323121:23

    Set the RTC

    Run the RTClib ds3231 example.

  2. UNODS18B2028.6°C

    Wire the probe and the Uno

    As in the table.

  3. UNODS18B2028.6°C

    Check the probe in ice water

    Near 0 degrees.

  4. UNOHelloPCF8574

    Upload the sketch

    Check the LCD.

  5. UNO

    Test the alarm with a lower limit

    Set LIMIT_C to 20 for a test.

  6. UNODS18B2028.6°C

    Fit the probe in the tank pocket

    Dry, and sealed against water.

  7. UNO

    Put the electronics in a box

    Away from splashes.

  8. UNO

    Review the SD log after a day

    Open milk.csv.

In short

How do you build a milk cooler temperature logger?

A probe in a bulk milk cooler logs temperature every minute to an SD card and sounds a local alarm if milk stays above 4 degrees for 20 minutes. You need Arduino Uno R3, DS18B20 waterproof probe, Resistor 4.7 kΩ, MicroSD Card Module, DS3231 RTC module, 16x2 LCD with I2C backpack (PCF8574), Active buzzer 5 V, Tactile push button 6 mm and Jumper wires male to male (40 pcs, 20 cm). It takes 8 steps and about 150 minutes.

Level
Intermediate
Time
About 150 min
Parts
9

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
DS18B20 probe red, black, yellowUno 5V, GND, D2 with 4.7 k from D2 to 5VMilk temperature
DS3231 SDA and SCLUno A4 and A5Real-time clock
LCD I2C SDA and SCLUno A4 and A5Display (same I2C bus)
DS3231 and LCD VCC and GNDUno 5V and GNDPower
SD module CS, MOSI, MISO, SCKUno D10, D11, D12, D13Storage
SD module VCC and GNDUno 5V and GNDPower
Buzzer plus and minusUno D6 and GNDAlarm
Silence buttonUno D7 to GNDInternal pull-up

Code

A stainless steel DS18B20 probe sits in a pocket in the tank wall (never in the milk itself unless it is a food-grade sheathed probe you can clean) and the Uno writes the temperature to an SD card once a minute with the time from the DS3231, giving a record you can review. A short rise, such as when the lid is opened, should not trigger an alarm, so the buzzer only sounds after the milk has stayed above the limit for twenty minutes in a row. A missing or broken probe also raises the alarm, because a silent logger is worse than none. A daily summary line (highest, lowest, minutes above the limit) is written at 8 am. The limit and delay are placed at the top of the sketch: confirm the correct values with your dairy's quality rules before relying on them. This is a helpful logger, not a certified food-safety record or a replacement for the cooler's own controls. This version has a local buzzer and display only; sending an SMS needs a mobile network module and is a good later upgrade. Use the DS18B20's 4.7 k pull-up and keep the cable short. Calibrate the probe in a glass of ice water (it should read near 0 degrees) and note any offset. Setup: Arduino IDE, board "Arduino Uno". Install RTClib, OneWire, DallasTemperature, and LiquidCrystal_I2C.

Runs on a virtual Arduino Uno in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <SPI.h>
#include <SD.h>
#include <Wire.h>
#include <RTClib.h>
#include <OneWire.h>
#include <DallasTemperature.h>
#include <LiquidCrystal_I2C.h>

const uint8_t ONEWIRE_PIN = 2, SD_CS = 10, BUZZER = 6, SILENCE = 7;
const float LIMIT_C = 4.0;                  // the limit you are checking against, confirm yours
const uint8_t ALARM_AFTER_MIN = 20;         // ignore short spikes such as a lid open for a minute

OneWire ow(ONEWIRE_PIN);
DallasTemperature ds(&ow);
RTC_DS3231 rtc;
LiquidCrystal_I2C lcd(0x27, 16, 2);          // change 0x27 to 0x3F if the screen stays blank

uint8_t minutesAbove = 0;
bool silenced = false;
float dayMax = -100, dayMin = 100;
uint16_t dayMinAbove = 0;
int lastMinute = -1, lastSummaryDay = -1;

void logLine(const char *tag, float v) {
  File f = SD.open("milk.csv", FILE_WRITE);
  if (!f) return;
  f.print(rtc.now().timestamp());
  f.print(',');
  f.print(tag);
  f.print(',');
  f.println(v, 1);
  f.close();
}

void setup() {
  pinMode(BUZZER, OUTPUT);
  pinMode(SILENCE, INPUT_PULLUP);
  lcd.init(); lcd.backlight();
  ds.begin();
  rtc.begin();
  SD.begin(SD_CS);
  lcd.print("Milk logger");
}

void loop() {
  DateTime n = rtc.now();
  if (!digitalRead(SILENCE)) silenced = true;

  if (n.minute() != lastMinute) {            // once a minute
    lastMinute = n.minute();
    ds.requestTemperatures();
    float t = ds.getTempCByIndex(0);
    bool bad = (t == DEVICE_DISCONNECTED_C);
    lcd.clear();
    if (bad) {
      lcd.print("PROBE FAULT");
      logLine("PROBE_FAULT", 0);
      minutesAbove = ALARM_AFTER_MIN;         // treat a missing probe as an alarm
    } else {
      lcd.print("Milk "); lcd.print(t, 1); lcd.print(" C");
      logLine("T", t);
      if (t > dayMax) dayMax = t;
      if (t < dayMin) dayMin = t;
      if (t > LIMIT_C) { if (minutesAbove < 255) minutesAbove++; dayMinAbove++; }
      else { minutesAbove = 0; silenced = false; }
    }
    lcd.setCursor(0, 1);
    lcd.print(minutesAbove >= ALARM_AFTER_MIN ? "ALARM TOO WARM " : "OK");
    if (n.hour() == 8 && n.minute() == 0 && n.day() != lastSummaryDay) {   // daily summary at 8 am
      lastSummaryDay = n.day();
      logLine("DAY_MAX", dayMax);
      logLine("DAY_MIN", dayMin);
      logLine("MIN_ABOVE_LIMIT", dayMinAbove);
      dayMax = -100; dayMin = 100; dayMinAbove = 0;
    }
  }
  if (minutesAbove >= ALARM_AFTER_MIN && !silenced) {
    digitalWrite(BUZZER, (millis() / 500) % 2);          // beep until silenced or cooled
  } else {
    digitalWrite(BUZZER, LOW);
  }
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Probe in ice waterAbout 0 degrees on the LCD
Probe in warm water, with LIMIT_C set to 20 and ALARM_AFTER_MIN set to 2Alarm starts after two minutes
Press the silence buttonBuzzer stops until it cools
Unplug the probePROBE FAULT and alarm
Read the SD cardOne row per minute

If it does not work

LCD blank

Try address 0x3F, or turn the contrast screw.

Reads -127

Probe not connected or the pull-up resistor missing.

No SD rows

Format FAT32 and check CS on D10.

Wrong time

RTC not set, or the coin cell is flat.

Alarm too sensitive

Raise ALARM_AFTER_MIN.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the milk cooler temperature logger?

Arduino Uno R3, DS18B20 waterproof probe, Resistor 4.7 kΩ, MicroSD Card Module, DS3231 RTC module, 16x2 LCD with I2C backpack (PCF8574), Active buzzer 5 V, Tactile push button 6 mm and Jumper wires male to male (40 pcs, 20 cm).

How long does the milk cooler temperature logger take to build?

About 150 minutes for a intermediate maker, in 8 steps.

How do I know the milk cooler temperature logger works?

Probe in ice water: About 0 degrees on the LCD. Probe in warm water, with LIMIT_C set to 20 and ALARM_AFTER_MIN set to 2: Alarm starts after two minutes. Press the silence button: Buzzer stops until it cools.

LCD blank: what should I check?

Try address 0x3F, or turn the contrast screw.

Reads -127: what should I check?

Probe not connected or the pull-up resistor missing.

No SD rows: what should I check?

Format FAT32 and check CS on D10.

Wrong time: what should I check?

RTC not set, or the coin cell is flat.