Projects / Eight-digit event counter

Eight-digit event counter

Beginner2 hGuided buildReviewed

Build it step by step

0 of 8 done
  1. NANO

    Wire the display

    VCC and GND, DIN to D12, CLK to D11, CS to D10.

  2. NANO

    Wire the buttons

    Count on D2, reset on D3, both to GND.

  3. NANO

    Upload the sketch

    The display shows 00000000.

  4. NANO12:45

    Press the count button

    The last digit goes up.

  5. NANO12:45

    Press it ten times

    The tens digit changes.

  6. NANO

    Wait five seconds, then unplug and replug

    The count is remembered.

  7. NANO

    Hold the reset button for two seconds

    The count returns to zero.

  8. NANO

    Try changing the brightness

    Edit the setIntensity value.

In short

How do you build an eight-digit event counter?

A big counter shows visitors, laps or parts counted using an eight-digit display and a button or sensor. You need Arduino Nano, 8-digit 7-segment module (MAX7219), Tactile push button 6 mm × 2 and Breadboard 830 Tie Points. It takes 8 steps and about 120 minutes.

Level
Beginner
Time
About 120 min
Parts
4

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Module VCCNano 5VPower
Module GNDNano GNDGround
Module DINNano D12Data
Module CLKNano D11Clock
Module CSNano D10Chip select
Count buttonNano D2 to GNDAdds one
Reset buttonNano D3 to GNDHold for two seconds to reset

Code

The MAX7219 is a display driver chip that scans up to eight seven-segment digits for you, so the board only sends numbers over three wires and the chip keeps them lit and bright. The LedControl library gives a setDigit function for each digit position. The sketch splits the count into digits and sends each one, filling unused places with zeros. A button adds one to the count; a debounce delay avoids double counts. The reset button must be held for two seconds so an accidental press does not wipe the number. The count is saved in the board's EEPROM, which keeps it through a power cut, but because EEPROM cells wear out after about a hundred thousand writes, the sketch waits until counting has paused for five seconds before saving. Replace the button with a sensor such as an infrared break-beam to count visitors, laps or parts on a line. Set the brightness with setIntensity: a lower value is easier on the eyes and uses less current.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <LedControl.h>
#include <EEPROM.h>

LedControl lc(12, 11, 10, 1);               // DIN, CLK, CS, one chip
const int COUNT_BTN = 2, RESET_BTN = 3;

unsigned long count = 0;
unsigned long lastChange = 0;
bool dirty = false;

void showCount() {
  unsigned long v = count;
  for (int pos = 0; pos < 8; pos++) {        // position 0 is the right-most digit
    lc.setDigit(0, pos, v % 10, false);
    v /= 10;
  }
}

void setup() {
  pinMode(COUNT_BTN, INPUT_PULLUP);
  pinMode(RESET_BTN, INPUT_PULLUP);
  lc.shutdown(0, false);
  lc.setIntensity(0, 4);
  lc.clearDisplay(0);
  EEPROM.get(0, count);
  if (count > 99999999UL) count = 0;         // blank EEPROM reads as a huge number
  showCount();
}

void loop() {
  if (digitalRead(COUNT_BTN) == LOW) {
    delay(30);
    if (digitalRead(COUNT_BTN) == LOW) {
      count++; dirty = true; lastChange = millis();
      showCount();
      while (digitalRead(COUNT_BTN) == LOW) {}
      delay(30);
    }
  }

  if (digitalRead(RESET_BTN) == LOW) {
    unsigned long t0 = millis();
    while (digitalRead(RESET_BTN) == LOW && millis() - t0 < 2000) {}
    if (millis() - t0 >= 2000) { count = 0; dirty = true; lastChange = millis(); showCount(); }
    while (digitalRead(RESET_BTN) == LOW) {}
  }

  if (dirty && millis() - lastChange > 5000) {   // save only after the counting pauses, to spare the EEPROM
    EEPROM.put(0, count);
    dirty = false;
  }
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Ten pressesDisplay shows 00000010
Hold the count buttonOne count only
Power cycle after countingCount restored
Reset held 2 seconds00000000
Reset tappedNo change

If it does not work

Display blank

Check power, DIN, CLK and CS wires and the shutdown call.

Digits in reverse order

Change the position order in showCount.

Counts jump by two

Increase the debounce delay.

Number resets after power cut

Wait five seconds after the last count before power off.

Dim display

Raise the setIntensity value.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the eight-digit event counter?

Arduino Nano, 8-digit 7-segment module (MAX7219), Tactile push button 6 mm × 2 and Breadboard 830 Tie Points.

How long does the eight-digit event counter take to build?

About 120 minutes for a beginner maker, in 8 steps.

How do I know the eight-digit event counter works?

Ten presses: Display shows 00000010. Hold the count button: One count only. Power cycle after counting: Count restored.

Display blank: what should I check?

Check power, DIN, CLK and CS wires and the shutdown call.

Digits in reverse order: what should I check?

Change the position order in showCount.

Counts jump by two: what should I check?

Increase the debounce delay.

Number resets after power cut: what should I check?

Wait five seconds after the last count before power off.