Projects / Light-seeking robot

Light-seeking robot

Beginner1.3 hGuided buildReviewed

Build it step by step

0 of 6 done
  1. UNOROBOT744 lux

    Mount the LDRs

    Fix two LDRs at the front, left and right, angled outwards by about 30 degrees, with a small card between them so each sees mostly its own side.

  2. UNO745 lux

    Build the dividers

    Each LDR from 5V to its analog pin, with 10 kΩ from the pin to GND.

  3. UNO

    Wire the motors

    Follow the wiring table and join all grounds.

  4. UNO746 lux

    Read the sensors

    Open the serial monitor and shine a torch at each LDR to see the readings change.

  5. UNOROBOT

    Test steering

    Hold the robot and move the torch to the left. The left wheel should slow and the right speed up.

  6. UNO

    Set it down in a dim room

    Put a torch in front and drive it towards the light.

In short

How do you build a light-seeking robot?

Two LDRs on the front make a robot steer towards a torch, like a moth, using the difference between them. You need Arduino Uno R3, LDR Photoresistor × 2, Resistor 10 kΩ × 2, L298N Dual H-Bridge Module, Robot car chassis kit 2WD (acrylic), Battery holder 18650 2S (series), 18650 cell 2600 mAh (branded) × 2, Jumper wires male to male (40 pcs, 20 cm) and Breadboard 400 points (half size). It takes 6 steps and about 75 minutes.

Level
Beginner
Time
About 75 min
Parts
9

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Left LDRUno 5V and A0, with 10 kΩ from A0 to GNDLeft divider, brighter gives a higher reading
Right LDRUno 5V and A1, with 10 kΩ from A1 to GNDRight divider
L298N ENA, IN1, IN2Uno D5, D7, D8Left motor
L298N ENB, IN3, IN4Uno D6, D9, D10Right motor
Battery pack +L298N 12 V terminal and Uno VINSupply from two 18650 cells
Battery pack -L298N GND and Uno GNDCommon ground

Code

Arduino IDE, board "Arduino Uno". No libraries. The thresholds of 900 and 150 depend on your room and LDRs. Read the values on the serial monitor and adjust.

Runs on a virtual Arduino Uno in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

const byte ENA = 5, IN1 = 7, IN2 = 8, ENB = 6, IN3 = 9, IN4 = 10;
const int BASE = 150;
const float GAIN = 0.4;

void drive(int l, int r) {
  l = constrain(l, 0, 255); r = constrain(r, 0, 255);
  digitalWrite(IN1, HIGH); digitalWrite(IN2, LOW);
  digitalWrite(IN3, HIGH); digitalWrite(IN4, LOW);
  analogWrite(ENA, l); analogWrite(ENB, r);
}

void setup() {
  for (byte p = 5; p <= 10; p++) pinMode(p, OUTPUT);
  Serial.begin(9600);
}

void loop() {
  int left = analogRead(A0), right = analogRead(A1);
  int diff = left - right;                     // positive: more light on the left
  Serial.print(left); Serial.print(' '); Serial.println(right);

  if (left > 900 && right > 900) {             // very bright on both: arrived
    drive(0, 0);
  } else if (left < 150 && right < 150) {      // too dark: stay still
    drive(0, 0);
  } else {
    // light on the left: slow the left wheel and speed up the right so it turns left
    drive(BASE - GAIN * diff, BASE + GAIN * diff);
  }
  delay(30);
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual Arduino Uno with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

512 513
512 512
513 512
512 512
511 511
512 511

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Torch on the left LDRLeft reading rises above the right one
Torch on the rightRobot turns right
Torch straight aheadDrives straight
Torch very closeStops when both readings are very bright

If it does not work

Turns away from the light

Swap the LDR connections or flip the sign of the difference.

Does not move

Both readings are below the dark limit. Lower the threshold or increase the room dimness difference.

Robot wiggles a lot

Reduce GAIN or add shading between the LDRs.

One wheel never turns

Check the L298N enable jumpers and the IN wires.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the light-seeking robot?

Arduino Uno R3, LDR Photoresistor × 2, Resistor 10 kΩ × 2, L298N Dual H-Bridge Module, Robot car chassis kit 2WD (acrylic), Battery holder 18650 2S (series), 18650 cell 2600 mAh (branded) × 2, Jumper wires male to male (40 pcs, 20 cm) and Breadboard 400 points (half size).

How long does the light-seeking robot take to build?

About 75 minutes for a beginner maker, in 6 steps.

How do I know the light-seeking robot works?

Torch on the left LDR: Left reading rises above the right one. Torch on the right: Robot turns right. Torch straight ahead: Drives straight.

Turns away from the light: what should I check?

Swap the LDR connections or flip the sign of the difference.

Does not move: what should I check?

Both readings are below the dark limit. Lower the threshold or increase the room dimness difference.

Robot wiggles a lot: what should I check?

Reduce GAIN or add shading between the LDRs.

One wheel never turns: what should I check?

Check the L298N enable jumpers and the IN wires.