Battery level indicator with zeners
Build it step by step
0 of 6 doneBuild stage one
Wire the 5.1 V zener, red LED and 1 kΩ in series across the supply.
Test stage one
Apply 9 V and see the LED light, then drop to 6 V to see it go out.
Build the other stages
Add the yellow and green stages with their zeners and 330 Ω resistors.
Make a variable supply
Set an MT3608 module from the 12 V adapter and sweep its output from 5 to 15 V, watching the meter.
Note the thresholds
Write down the voltage at which each LED comes on.
Use it on a battery
Check a 12 V battery shows about two LEDs when fully charged.
How do you build a battery level indicator with zeners?
Zener diodes of different voltages light LEDs in steps as a 12 V battery rises, with no chip. You need Zener diode 5.1 V (1N4733A), Zener diode 9.1 V (1N4739A), Zener diode 12 V (1N4742A), LED 5 mm red, LED 5 mm yellow, LED 5 mm green, Resistor 1 kΩ, Resistor 330 Ω × 2, MT3608 Boost Module, 12 V 2 A DC adapter, Digital multimeter and Breadboard 830 Tie Points. It takes 6 steps and about 30 minutes.
- Level
- Beginner
- Time
- About 30 min
- Parts
- 12
Parts list
- SemiconductorsBuy
- SemiconductorsBuy
- SemiconductorsBuy
- SemiconductorsBuyLED 5 mm red × 1
- SemiconductorsBuyLED 5 mm yellow × 1
- SemiconductorsBuyLED 5 mm green × 1
- PassivesBuyResistor 1 kΩ × 1
- PassivesBuyResistor 330 Ω × 2
- PowerBuy
- PowerBuy
- Tools & InstrumentsBuy
- PrototypingBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| Supply + (battery or MT3608 output) | Breadboard + rail | Input to be measured |
| Supply - | Breadboard - rail | Ground |
| Stage 1: + rail | Zener 5.1 V cathode (band) | Lowest step |
| Zener 5.1 V anode | Red LED anode | In series |
| Red LED cathode | 1 kΩ resistor, then - rail | Limits current |
| Stage 2: + rail | Zener 9.1 V cathode (band) | Middle step |
| Zener 9.1 V anode | Yellow LED anode | In series |
| Yellow LED cathode | 330 Ω resistor, then - rail | Limits current |
| Stage 3: + rail | Zener 12 V cathode (band) | Top step |
| Zener 12 V anode | Green LED anode | In series |
| Green LED cathode | 330 Ω resistor, then - rail | Limits current |
No code needed
No code. Each LED turns on once the supply is above the zener voltage plus the LED's own drop of roughly 2 V, so the steps are about 7 V, 11 V and 14 V. These are approximate because zeners have 5% tolerance and LEDs vary. The LEDs are dim near their threshold, so use high-efficiency LEDs. Set a MT3608 boost module to a test voltage with a multimeter before connecting it, and never exceed 15 V.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Supply 6 V | No LED |
| Supply 9 V | Red on |
| Supply 12 V | Red and yellow on |
| Supply 15 V | All three on |
If it does not work
LED never lights
Zener is backwards. The band must face the + rail.
All LEDs always on
Zeners are shorted or missing from the series path.
LED too dim
The supply is only just above the step. Raise it or use a lower resistor.
Steps are in the wrong places
Check the zener values printed on the parts.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the battery level indicator with zeners?
Zener diode 5.1 V (1N4733A), Zener diode 9.1 V (1N4739A), Zener diode 12 V (1N4742A), LED 5 mm red, LED 5 mm yellow, LED 5 mm green, Resistor 1 kΩ, Resistor 330 Ω × 2, MT3608 Boost Module, 12 V 2 A DC adapter, Digital multimeter and Breadboard 830 Tie Points.
How long does the battery level indicator with zeners take to build?
About 30 minutes for a beginner maker, in 6 steps.
How do I know the battery level indicator with zeners works?
Supply 6 V: No LED. Supply 9 V: Red on. Supply 12 V: Red and yellow on.
LED never lights: what should I check?
Zener is backwards. The band must face the + rail.
All LEDs always on: what should I check?
Zeners are shorted or missing from the series path.
LED too dim: what should I check?
The supply is only just above the step. Raise it or use a lower resistor.
Steps are in the wrong places: what should I check?
Check the zener values printed on the parts.
