Build it step by step
0 of 7 doneTest each colour
Wire each LED with 1 kΩ to 9 V and measure its forward voltage.
Make a table
Record the colour and Vf for red, yellow, green, blue and white.
Choose a current
Pick 10 mA, a typical bright value.
Calculate
Work out R = (9 V − Vf) ÷ 10 mA for each LED.
Pick the nearest resistor
Use the next higher standard value from your kit.
Measure the actual current
Put the meter in series and check it matches your prediction.
Compare brightness
See how the brightness changes at 3 mA, 7 mA and 15 mA.
How do you build an LED resistor lab?
Light LEDs of different colours, measure their forward voltage and choose the right resistor for each. You need LED 5 mm red, LED 5 mm green, LED 5 mm blue, LED 5 mm white, LED 5 mm yellow, Resistor 220 Ω × 2, Resistor 330 Ω × 2, Resistor 1 kΩ, Digital multimeter, Breadboard 830 Tie Points, 9 V battery and 9 V battery snap with DC jack. It takes 7 steps and about 30 minutes.
- Level
- Beginner
- Time
- About 30 min
- Parts
- 12
Parts list
- SemiconductorsBuyLED 5 mm red × 1
- SemiconductorsBuyLED 5 mm green × 1
- OptoelectronicsBuyLED 5 mm blue × 1
- OptoelectronicsBuyLED 5 mm white × 1
- SemiconductorsBuyLED 5 mm yellow × 1
- PassivesBuyResistor 220 Ω × 2
- PassivesBuyResistor 330 Ω × 2
- PassivesBuyResistor 1 kΩ × 1
- Tools & InstrumentsBuy
- PrototypingBuy
- BatteriesBuy9 V battery × 1
- PowerBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| 9 V battery + | 1 kΩ, then LED anode | Safe test current of about 7 mA |
| LED cathode | 9 V battery - | Return |
| Meter in volts | Across the LED | Reads the forward voltage |
| Meter in mA | In series with the LED branch | Reads the current |
No code needed
No code. R = (Vsupply − Vf) ÷ I. For a red LED (Vf about 2 V) at 9 V and 10 mA that is 700 Ω, so choose the next standard value above, here 1 kΩ for about 7 mA. Blue and white LEDs have Vf near 3 V, so the same resistor gives a little less current.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Red LED | Forward voltage about 1.8 to 2.1 V |
| Blue or white LED | About 2.8 to 3.3 V |
| Current with 1 kΩ at 9 V | About 6 to 7 mA |
| Calculated against measured current | Within 10 to 15 percent |
If it does not work
LED does not light
Reversed. The long leg is the anode and goes towards the resistor.
LED burns out
No resistor or too small a resistor. Always calculate first.
Meter shows 0 mA
The meter is in the wrong socket or the circuit is open.
Forward voltage reads high
The meter is measuring in a different range. Use the 20 V range.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the LED resistor lab?
LED 5 mm red, LED 5 mm green, LED 5 mm blue, LED 5 mm white, LED 5 mm yellow, Resistor 220 Ω × 2, Resistor 330 Ω × 2, Resistor 1 kΩ, Digital multimeter, Breadboard 830 Tie Points, 9 V battery and 9 V battery snap with DC jack.
How long does the LED resistor lab take to build?
About 30 minutes for a beginner maker, in 7 steps.
How do I know the LED resistor lab works?
Red LED: Forward voltage about 1.8 to 2.1 V. Blue or white LED: About 2.8 to 3.3 V. Current with 1 kΩ at 9 V: About 6 to 7 mA.
LED does not light: what should I check?
Reversed. The long leg is the anode and goes towards the resistor.
LED burns out: what should I check?
No resistor or too small a resistor. Always calculate first.
Meter shows 0 mA: what should I check?
The meter is in the wrong socket or the circuit is open.
Forward voltage reads high: what should I check?
The meter is measuring in a different range. Use the 20 V range.
