Projects / LED cosplay goggles

LED cosplay goggles

Beginner1.5 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. XIAO15.5 mA

    Test one ring

    Light all 16 LEDs red at low brightness.

  2. XIAO15.5 mA

    Chain both rings

    Light 32 LEDs.

  3. XIAO15.5 mA

    Write the comet

    Spin it around both rings.

  4. XIAO

    Add the colour wheel

    Fade through colours slowly.

  5. XIAO

    Add the button

    Cycle through effects.

  6. XIAO+

    Add the battery

    Fit a LiPo in a pouch.

  7. XIAO

    Build the goggles

    Diffuser film and a soft strap.

In short

How do you build an LED cosplay goggles?

Two 16-LED rings in goggles spin, blink and change colour for cosplay or a party. You need Seeed XIAO RP2040, WS2812B ring 16 LEDs × 2, Li-Po battery 3.7 V 1000 mAh and Tactile push button 6 mm. It takes 7 steps and about 90 minutes.

Level
Beginner
Time
About 90 min
Parts
4

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Ring 1 DINXIAO D0Data
Ring 1 DOUTRing 2 DINChain
Rings VCC and GNDXIAO 3V3 and GNDPower (use a protected LiPo, keep brightness low)
ButtonXIAO D1 and GNDNext effect
LiPoXIAO BAT padsPower and charging

Code

Two 16-LED rings are chained on one pin, so the code treats them as one strip of 32. Brightness is capped at about 10 percent, which is comfortable close to the eyes and keeps the current low enough for a small battery; full white from 32 LEDs would take about 2 A. Avoid fast flashing: flicker at 3 to 30 flashes per second can trigger seizures in people with photosensitive epilepsy, so the effects here fade or step slowly, and the blink is slow. Build the goggles so the LEDs shine out and do not shine into the wearer's eyes, with diffuser film over the rings. Use a protected LiPo in a sewn pocket, never wear it while charging, and make sure the goggles never block the wearer's view in a way that is unsafe, such as on a road or stairs. Arduino IDE with the Raspberry Pi Pico/RP2040 boards package by Earle Philhower, board "Seeed XIAO RP2040".

Runs on a virtual Seeed XIAO RP2040 in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// LED goggles: three effects, button to change. Board: Seeed XIAO RP2040. Library: Adafruit NeoPixel.
#include <Adafruit_NeoPixel.h>
Adafruit_NeoPixel px(32, D0, NEO_GRB + NEO_KHZ800);     // two rings of 16
const int BTN = D1;
int effect = 0; unsigned long lastBtn = 0; int pos = 0, hue = 0;

void setup() {
  pinMode(BTN, INPUT_PULLUP);
  px.begin(); px.setBrightness(25);                     // low brightness: comfortable near the eyes and easy on the battery
}

void loop() {
  if (!digitalRead(BTN) && millis() - lastBtn > 300) { effect = (effect + 1) % 3; lastBtn = millis(); px.clear(); }
  px.clear();
  if (effect == 0) {                                    // spinning comet on both rings
    for (int t = 0; t < 5; t++) {
      uint8_t b = 255 - t * 50;
      px.setPixelColor((pos - t + 16) % 16, px.Color(0, b, b));
      px.setPixelColor(16 + (pos - t + 16) % 16, px.Color(0, b, b));
    }
    pos = (pos + 1) % 16; px.show(); delay(60);
  } else if (effect == 1) {                             // colour wheel, slow fade
    for (int i = 0; i < 32; i++) px.setPixelColor(i, px.gamma32(px.ColorHSV(hue + (i % 16) * 4096)));
    hue += 300; px.show(); delay(30);
  } else {                                              // gentle eye blink, no fast flashing
    px.fill(px.Color(255, 40, 0)); px.show(); delay(1800);
    px.clear(); px.show(); delay(150);
  }
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Power onComet spins on both rings
Press the buttonColour wheel, then eye blink
Look at a mirrorEffects are comfortable, no harsh flicker
BatteryLasts a few hours

If it does not work

Wrong colours

Change NEO_GRB to NEO_RGB.

Second ring dark

Check DOUT of ring 1 goes to DIN of ring 2.

Too bright

Lower setBrightness.

Battery drains fast

Lower brightness or use fewer LEDs.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the LED cosplay goggles?

Seeed XIAO RP2040, WS2812B ring 16 LEDs × 2, Li-Po battery 3.7 V 1000 mAh and Tactile push button 6 mm.

How long does the LED cosplay goggles take to build?

About 90 minutes for a beginner maker, in 7 steps.

How do I know the LED cosplay goggles works?

Power on: Comet spins on both rings. Press the button: Colour wheel, then eye blink. Look at a mirror: Effects are comfortable, no harsh flicker.

Wrong colours: what should I check?

Change NEO_GRB to NEO_RGB.

Second ring dark: what should I check?

Check DOUT of ring 1 goes to DIN of ring 2.

Too bright: what should I check?

Lower setBrightness.

Battery drains fast: what should I check?

Lower brightness or use fewer LEDs.