Projects / LED forward voltage by colour

LED forward voltage by colour

Beginner1 hGuided buildReviewed

Build it step by step

0 of 8 done
  1. 13.2 mA

    Wire the test circuit

    5 V, 330 ohm, LED, back to 5 V negative.

  2. 13.2 mA

    Light the first LED

    Check the long leg is on the resistor side.

  3. 13.2 mA

    Measure the voltage

    Meter directly across the LED legs.

  4. Note the current

    Calculate it from the resistor.

  5. 13.3 mA

    Swap in each colour

    Repeat for every LED in the pack.

  6. Order the table

    Sort by wavelength.

  7. Compare

    Check each against 1240 divided by the wavelength.

  8. 13.3 mA

    Explain

    Why blue LEDs need a higher voltage.

In short

How do you build an LED forward voltage by colour?

Measure the forward voltage of LEDs of each colour at one current and build a table linking colour to voltage. You need LED 3 mm assorted pack, Resistor 330 Ω, 5 V 2 A USB adapter, Digital multimeter, Jumper wires male to male (40 pcs, 20 cm) and Breadboard 830 Tie Points. It takes 8 steps and about 60 minutes.

Level
Beginner
Time
About 60 min
Parts
6

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
5 V adapter positive330 ohm resistorSeries resistor
330 ohm resistorLED anode (long leg)LED under test
LED cathode (short leg)5 V adapter negativeCommon ground
Multimeter red probeLED anodeReads the forward voltage
Multimeter black probeLED cathodeReads the forward voltage

Code

Every LED has a forward voltage, the voltage that must be across it before it conducts and lights, and it depends on the colour. Red LEDs need about 2 volts, green are in the same range or higher, and blue and white need about 3 volts. The reason is physics: a photon of red light has less energy than a photon of blue light, and the LED material must provide at least that energy for each electron, so a rough rule is that the energy in electron volts is 1240 divided by the wavelength in nanometres. That makes red at 630 nanometres about 2 volts and blue at 470 nanometres about 2.6, with the real forward voltage a little higher. This lab turns the idea into a table. Use the same 330 ohm resistor and a 5 volt supply for each LED so the current is about the same, then measure the voltage directly across the LED legs while it is lit. Also note the current from the voltage across the resistor, since 5 minus the LED voltage divided by 330 ohms shows that blue LEDs run at a lower current on the same resistor, which is why they look dimmer. The table also explains why a red LED can run from two AA cells but a white one cannot, and why a simple battery light needs a resistor sized for the colour.

Build notes (no code needed for this build)

Method: one LED at a time on the same 330 ohm resistor and 5 V supply, so the current is nearly the same for each colour.
Current = (5 V - forward voltage) / 330 ohm, so about 9 mA for red and about 5 to 6 mA for blue or white.
All of these are low and safe for 3 mm LEDs. Keep the resistor in the circuit for every test.

Measure the voltage across the LED legs with the meter on DC volts, with the circuit lit.

Record a table: colour, wavelength in nanometres (from the packet if given), forward voltage, calculated current.

Typical results, which vary a little between makers:
  Red     about 1.8 to 2.1 V
  Orange  about 1.9 to 2.2 V
  Yellow  about 1.9 to 2.2 V
  Green   about 2.0 to 3.0 V (standard green about 2.1 V, pure green close to 3 V)
  Blue    about 2.8 to 3.3 V
  White   about 2.8 to 3.3 V

Why: light energy is about 1240 divided by the wavelength in nanometres, in electron volts, and an LED needs at least that much voltage.
Red at 630 nm gives about 2.0 V, blue at 470 nm gives about 2.6 V, and the real forward voltage is a little above those numbers.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Red LEDAbout 1.8 to 2.1 V
Green LEDAbout 2.0 to 3.0 V
Blue LEDAbout 2.8 to 3.3 V
White LEDAbout 2.8 to 3.3 V
CurrentsAll between about 4 and 10 mA

If it does not work

LED does not light

Check the direction and the supply.

Voltage reads 5 V

The LED is open or the legs are wrong, swap it.

Reading changes

Check the resistor and keep the same supply.

LED very dim

A blue or white LED draws less current on the same resistor.

Meter reads zero

Check the probes touch the LED legs.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the LED forward voltage by colour?

LED 3 mm assorted pack, Resistor 330 Ω, 5 V 2 A USB adapter, Digital multimeter, Jumper wires male to male (40 pcs, 20 cm) and Breadboard 830 Tie Points.

How long does the LED forward voltage by colour take to build?

About 60 minutes for a beginner maker, in 8 steps.

How do I know the LED forward voltage by colour works?

Red LED: About 1.8 to 2.1 V. Green LED: About 2.0 to 3.0 V. Blue LED: About 2.8 to 3.3 V.

LED does not light: what should I check?

Check the direction and the supply.

Voltage reads 5 V: what should I check?

The LED is open or the legs are wrong, swap it.

Reading changes: what should I check?

Check the resistor and keep the same supply.

LED very dim: what should I check?

A blue or white LED draws less current on the same resistor.