Projects / Keypad encoder with gates

Keypad encoder with gates

Intermediate2 hGuided buildReviewed

Build it step by step

0 of 8 done
  1. UNO

    Draw the truth table

    Write it on paper first.

  2. UNO

    Derive the equations

    One per output bit.

  3. UNO

    Power the breadboard

    5 V and GND rails from the Uno.

  4. UNO

    Place the three chips

    Add power pins 14 and 7 on each.

  5. UNO74HC32

    Wire the A2 section

    Three gates on U1, test with keys 4 to 7.

  6. UNO

    Wire A1 and A0

    Same pattern on U2 and U3.

  7. UNO74HC32

    Wire the VALID flag

    Gate 4 of each chip.

  8. UNO13.1 mA

    Add the LEDs and test every key

    Check the table.

In short

How do you build a keypad encoder with gates?

Turn eight buttons into a 3-bit binary code and a key-pressed flag using only twelve OR gates on three 74HC32 chips. You need 74HC32 quad OR gate × 3, Tactile push button 6 mm × 8, Resistor 10 kΩ × 8, LED 5 mm red × 4, Resistor 330 Ω × 4, Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm) and Arduino Uno R3. It takes 8 steps and about 120 minutes.

Level
Intermediate
Time
About 120 min
Parts
8

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Arduino Uno 5V and GNDBreadboard power railsSupply for all chips (74HC32 allows 2 to 6 V)
Each 74HC32 pin 14 and pin 75 V rail and GND railPower every chip
Buttons I0 to I7Each button from the 5 V rail to its own input node, with a 10 k from that node to GNDActive-high inputs
U1 gate 1 (pins 1,2 to 3)I4 and I5 in, output to pin 9First half of A2
U1 gate 2 (pins 4,5 to 6)I6 and I7 in, output to pin 10Second half of A2
U1 gate 3 (pins 9,10 to 8)Pin 8 is A2MSB of the code
U2 gates 1 and 2I2 or I3, and I6 or I7, combined by gate 3 pin 8A1 (same wiring pattern as U1)
U3 gates 1 and 2I1 or I3, and I5 or I7, combined by gate 3 pin 8A0 (same wiring pattern)
U1 gate 4 (pins 12,13 to 11)A2 and A1 inPart of the valid flag
U2 gate 4 (pins 12,13 to 11)A0 and I0 inPart of the valid flag
U3 gate 4 (pins 12,13 to 11)U1 pin 11 and U2 pin 11 inPin 11 is the VALID output
A2, A1, A0, VALIDEach through a 330 Ω to an LED to GNDDisplay the code

Code

A priority-free encoder is just OR gates: each output bit is the OR of every key whose number has that bit set to one. Key 5 is binary 101, so it feeds A2 and A0. Key 0 is 000 and feeds nothing, which is why the VALID output exists: without it you could not tell key 0 from no key. A 74HC32 holds four two-input OR gates, so a four-input OR takes three gates, two in the first layer and one to join them. All twelve gates across three chips are used. Power it from the 5 V pin of an Uno over USB. No input is left floating because every key node has a pull-down resistor. Press two keys at once and the codes OR together, for example keys 1 and 2 give 3. That is the reason real encoders such as the 74HC148 add priority logic so the highest key wins; try replacing this circuit with a 74HC148 and compare. Build it on the breadboard one output at a time and test with a multimeter or the LEDs before adding the next.

Truth table for the encoder (inputs are active high, 1 means pressed)

Key   A2 A1 A0   Valid
I0     0  0  0     1   (needs the valid flag, otherwise it looks like "nothing pressed")
I1     0  0  1     1
I2     0  1  0     1
I3     0  1  1     1
I4     1  0  0     1
I5     1  0  1     1
I6     1  1  0     1
I7     1  1  1     1
none   0  0  0     0

Boolean equations (each OR gate has two inputs, so chain them)
A2 = I4 + I5 + I6 + I7        = (I4 + I5) + (I6 + I7)
A1 = I2 + I3 + I6 + I7        = (I2 + I3) + (I6 + I7)
A0 = I1 + I3 + I5 + I7        = (I1 + I3) + (I5 + I7)
VALID = I0 + A2 + A1 + A0     = (A2 + A1) + (A0 + I0)

Gate count: three for each of A2, A1, A0 (nine) plus three for VALID (twelve) = exactly three 74HC32 chips.

74HC32 pinout (top view, notch up):
Gate 1: 1A 1B 1Y are pins 1,2,3 | Gate 2: 2A 2B 2Y are pins 4,5,6 | GND is pin 7
3Y 3A 3B are 8,9,10 | 4Y 4A 4B are 11,12,13 | VCC is 14

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Press no keyAll four LEDs off
Press key 0Only VALID lights
Press key 5A2, A0 and VALID light
Press key 7All four light
Press keys 1 and 2 togetherOutput shows 3, the OR of both

If it does not work

Random LED flicker

An input is floating; check each 10 k pull-down.

Everything lights

Input node touching the 5 V rail, or a missing GND on a chip.

One output stuck

Check the gate pins against the pinout and the chain between layers.

Chip gets warm

Supply wired backwards; unplug at once and check pin 14 and pin 7.

Key 0 shows nothing

Expected on A outputs; VALID must light.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the keypad encoder with gates?

74HC32 quad OR gate × 3, Tactile push button 6 mm × 8, Resistor 10 kΩ × 8, LED 5 mm red × 4, Resistor 330 Ω × 4, Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm) and Arduino Uno R3.

How long does the keypad encoder with gates take to build?

About 120 minutes for a intermediate maker, in 8 steps.

How do I know the keypad encoder with gates works?

Press no key: All four LEDs off. Press key 0: Only VALID lights. Press key 5: A2, A0 and VALID light.

Random LED flicker: what should I check?

An input is floating; check each 10 k pull-down.

Everything lights: what should I check?

Input node touching the 5 V rail, or a missing GND on a chip.

One output stuck: what should I check?

Check the gate pins against the pinout and the chain between layers.

Chip gets warm: what should I check?

Supply wired backwards; unplug at once and check pin 14 and pin 7.