Projects / Shop shelf stock monitor

Shop shelf stock monitor

Intermediate3 hGuided buildReviewed

Build it step by step

0 of 6 done
  1. ESP32++177 g

    Mount the cells

    Fix one end of each bar to the shelf and the other end to a tray.

  2. ESP32++178 g

    Wire the amplifiers

    Connect each cell to its HX711 and the HX711s to the ESP32.

  3. ESP32

    Tare

    With the trays empty send t1 and t2.

  4. ESP32

    Calibrate

    Put a known weight on a tray and send c1 followed by its mass in grams.

  5. ESP32

    Set the item weight

    Weigh one item and send u1 with its mass.

  6. ESP32

    Open the page

    Read the IP address and view the counts in a browser.

In short

How do you build a shop shelf stock monitor?

Load cells under shelf trays tell a shopkeeper when stock is low, shown on a small web page. You need ESP32 DevKit V1, Load cell 5 kg (bar type) × 2, HX711 load cell amplifier × 2 and 5 V 2 A USB adapter. It takes 6 steps and about 180 minutes.

Level
Intermediate
Time
About 180 min
Parts
4

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Load cell 1 four wiresHX711 board 1 E+, E-, A+, A-Shelf one
Load cell 2 four wiresHX711 board 2 E+, E-, A+, A-Shelf two
HX711 1 DT, SCKESP32 GPIO16, GPIO17Data and clock
HX711 2 DT, SCKESP32 GPIO18, GPIO19Data and clock
Both HX711 VCC, GNDESP32 3V3, GNDPower
5 V USB adapterESP32 USBPower

Code

Arduino IDE with the ESP32 boards package, board "ESP32 Dev Module". Install "HX711" by bogde. Put your own Wi-Fi details in the placeholders. Mount each bar-type cell with one end fixed and the shelf tray on the free end, leaving the cell free to flex, and never load it beyond 5 kg. With the empty tray in place, send t1 or t2 to tare, then c1 500 with a known weight, and u1 with the weight of a single item. Counts are only as accurate as the item weights are consistent.

Runs on a virtual ESP32 Dev Module in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <WiFi.h>
#include <WebServer.h>
#include <HX711.h>
#include <Preferences.h>

const char* WIFI_NAME = "YOUR_WIFI_NAME";
const char* WIFI_PASSWORD = "YOUR_WIFI_PASSWORD";
HX711 scale[2];
Preferences prefs;
float unitGrams[2] = { 100, 100 };           // weight of one item, set with the u command
int lowLimit[2] = { 5, 5 };
WebServer server(80);

int countOf(byte i) {
  float grams = scale[i].get_units(5);
  return max(0, (int)round(grams / unitGrams[i]));
}

void page() {
  String html = "<meta http-equiv='refresh' content='30'><body style='font-family:sans-serif'><h2>Shelf stock</h2>";
  for (byte i = 0; i < 2; i++) {
    int c = countOf(i);
    html += "<p>Shelf " + String(i + 1) + ": " + String(c) + " items";
    if (c < lowLimit[i]) html += " <b>(low, reorder)</b>";
    html += "</p>";
  }
  server.send(200, "text/html", html);
}

void setup() {
  Serial.begin(115200);
  scale[0].begin(16, 17); scale[1].begin(18, 19);
  prefs.begin("shelf", false);
  for (byte i = 0; i < 2; i++) {
    scale[i].set_scale(prefs.getFloat(("cal" + String(i)).c_str(), 1.0));
    unitGrams[i] = prefs.getFloat(("unit" + String(i)).c_str(), 100);
    scale[i].tare();
  }
  WiFi.begin(WIFI_NAME, WIFI_PASSWORD);
  while (WiFi.status() != WL_CONNECTED) delay(500);
  Serial.println(WiFi.localIP());
  server.on("/", page);
  server.begin();
}

void loop() {
  server.handleClient();
  // Serial commands: t1 tares shelf 1; c1 500 calibrates with a 500 g known weight; u1 120 sets item weight to 120 g
  if (Serial.available()) {
    char cmd = Serial.read(); int s = Serial.parseInt() - 1; float v = Serial.parseFloat();
    if (s < 0 || s > 1) return;
    if (cmd == 't') scale[s].tare();
    if (cmd == 'c' && v > 0) { scale[s].set_scale(); float f = scale[s].get_units(10) / v; scale[s].set_scale(f); prefs.putFloat(("cal" + String(s)).c_str(), f); Serial.println(f); }
    if (cmd == 'u' && v > 0) { unitGrams[s] = v; prefs.putFloat(("unit" + String(s)).c_str(), v); }
  }
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual ESP32 Dev Module with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

192.168.1.42

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Empty trays0 items
Ten items of 100 gAbout 10 items
Below the limitPage says low, reorder
RebootCalibration is remembered

If it does not work

Counts jump

Keep the tray still and use bars that are firmly mounted.

Negative or zero

Check the wire colours and that the load is in the arrow direction.

Wrong count

Re-weigh a single item and reset u.

Page not found

Check the IP address on the Serial Monitor.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the shop shelf stock monitor?

ESP32 DevKit V1, Load cell 5 kg (bar type) × 2, HX711 load cell amplifier × 2 and 5 V 2 A USB adapter.

How long does the shop shelf stock monitor take to build?

About 180 minutes for a intermediate maker, in 6 steps.

How do I know the shop shelf stock monitor works?

Empty trays: 0 items. Ten items of 100 g: About 10 items. Below the limit: Page says low, reorder.

Counts jump: what should I check?

Keep the tray still and use bars that are firmly mounted.

Negative or zero: what should I check?

Check the wire colours and that the load is in the arrow direction.

Wrong count: what should I check?

Re-weigh a single item and reset u.

Page not found: what should I check?

Check the IP address on the Serial Monitor.