Build it step by step
0 of 8 donePlace the timer
ICM7555 across the breadboard centre gap, note the notch for pin 1.
Power the chip
Pin 8 to battery positive, pin 1 to battery negative, pin 4 to positive.
Add RA and RB
100 kilohm from pin 8 to pin 7, 1 kilohm from pin 7 to pin 6.
Join pins 6 and 2
Then add the 10 microfarad capacitor to ground, stripe to ground.
Add the control capacitor
10 nanofarad from pin 5 to ground.
Wire the LED
Battery positive, 1 kilohm, LED anode, LED cathode to pin 3.
Measure the current
Meter in series with the battery.
Compare
Repeat with a steady LED and work out battery life.
How do you build a low-power 555 blinker?
A CMOS 555 timer flashes an LED briefly about once a second, so a 9 V battery lasts far longer than with a steady LED. You need ICM7555 / LMC555 CMOS timer, Resistor 100 kΩ, Resistor 1 kΩ × 2, Electrolytic capacitor 10 µF, Ceramic capacitor 10 nF, LED 5 mm red, 9 V battery, 9 V battery snap with DC jack, Digital multimeter and Breadboard 830 Tie Points. It takes 8 steps and about 120 minutes.
- Level
- Beginner
- Time
- About 120 min
- Parts
- 10
Parts list
- Integrated Circuits
- PassivesBuyResistor 100 kΩ × 1
- PassivesBuyResistor 1 kΩ × 2
- PassivesBuy
- PassivesBuy
- SemiconductorsBuyLED 5 mm red × 1
- BatteriesBuy9 V battery × 1
- PowerBuy
- Tools & InstrumentsBuy
- PrototypingBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| 9 V battery positive | ICM7555 pin 8 (V+), pin 4 (reset) and the 1 kilohm LED resistor | Power and reset held high |
| 9 V battery negative | ICM7555 pin 1 (GND) | Common ground |
| ICM7555 pin 8 | 100 kilohm resistor RA to pin 7 | Slow charge path, sets the long gap |
| ICM7555 pin 7 | 1 kilohm resistor RB to pin 6 | Short discharge path, sets the flash length |
| ICM7555 pin 6 joined to pin 2 | 10 microfarad capacitor positive leg | Timing capacitor, stripe leg to ground |
| 10 microfarad capacitor negative (stripe) | 9 V battery negative | Capacitor return |
| ICM7555 pin 5 | 10 nanofarad capacitor to GND | Control pin decoupling |
| 1 kilohm LED resistor | Red LED anode (long leg) | Current limit for the LED |
| Red LED cathode (short leg) | ICM7555 pin 3 (output) | The output sinks current to light the LED |
Code
A 555 timer in astable mode charges and discharges a capacitor between one third and two thirds of the supply. The charge goes through both RA and RB, but the discharge goes only through RB, so the output stays high for a time set by RA plus RB and low for a time set by RB alone. Here RA is 100 kilohm and RB is 1 kilohm, which makes a long high period and a very short low period. The LED is wired from the supply to the output, so it conducts only when the output is low, giving a short flash about every 0.7 seconds. The CMOS ICM7555 is the right choice for this because its own supply current is tiny, while the bipolar NE555 uses milliamps even when idle. Measuring the current with the meter in series shows the result clearly: a steady LED through 1 kilohm draws about 7 milliamps from 9 volts, while the blinker averages a fraction of a milliamp. Divide the battery capacity by each current to see why designers of beacons and trail markers use short pulses. Pin 5 is held steady with a small capacitor so noise does not disturb the timing, and pin 4 is tied high so the chip never resets. Respect the electrolytic capacitor polarity, as a reversed one can leak or fail.
Build notes (no code needed for this build) The ICM7555 is a CMOS version of the 555. Its supply current is a small fraction of a milliamp, and it works from about 2 V up to 18 V. The bipolar NE555 takes several milliamps, which would waste the battery. Astable timing (standard 555 formulas): output high time = 0.693 x (RA + RB) x C = 0.693 x 101 kilohm x 10 microfarad = about 0.70 s output low time = 0.693 x RB x C = 0.693 x 1 kilohm x 10 microfarad = about 7 ms frequency = 1.44 / ((RA + 2 x RB) x C) = about 1.4 flashes per second The LED is connected between the supply and the output, so it lights only while the output is LOW. That is the short 7 millisecond part of each cycle, which is why the average current is tiny. LED current while lit with the 9 V battery: (9 - 2.0) / 1000 = about 7 mA. Average LED current: 7 mA x 7 ms / 700 ms = about 0.07 mA. Add the chip's own supply current and the total is typically a few tenths of a milliamp or less. Method: 1. Build on the breadboard. The electrolytic capacitor has a stripe on the negative leg, keep that leg towards ground. 2. Connect the battery and watch for short flashes. 3. Put the multimeter in series with the battery on its mA range (red lead in the mA jack). The reading wanders as the LED pulses, so note the average. 4. Repeat with the 555 removed and the LED connected straight through its 1 kilohm resistor to the battery: about 7 mA. 5. Divide the battery capacity by each current to compare hours of life. A small 9 V alkaline battery of 500 mAh gives roughly 70 hours steady and many hundreds of hours blinking. 6. Return the red lead to the voltage jack. Because the flash is so short, the eye sees it as dimmer than a steady LED, so a high-brightness red LED helps. To lengthen the flash, make RB larger.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Connect the battery | Short flashes about once every 0.7 seconds |
| Count flashes for 30 seconds | About 40 flashes |
| Average battery current | A fraction of a milliamp |
| Steady LED comparison | About 7 mA |
| Make RB 10 kilohm | Flash lasts about 10 times longer, to about 70 ms |
If it does not work
No flashes
Check pin 1 and pin 8 power and that the LED is the right way round.
LED stays on
Pin 6 is not joined to pin 2 or the capacitor is not connected.
Very faint flash
Use a high-brightness LED or lengthen the flash with a larger RB.
Flashes too fast
Check RA is 100 kilohm and the capacitor is 10 microfarad.
Meter reads zero
Check the red lead is in the mA jack.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the low-power 555 blinker?
ICM7555 / LMC555 CMOS timer, Resistor 100 kΩ, Resistor 1 kΩ × 2, Electrolytic capacitor 10 µF, Ceramic capacitor 10 nF, LED 5 mm red, 9 V battery, 9 V battery snap with DC jack, Digital multimeter and Breadboard 830 Tie Points.
How long does the low-power 555 blinker take to build?
About 120 minutes for a beginner maker, in 8 steps.
How do I know the low-power 555 blinker works?
Connect the battery: Short flashes about once every 0.7 seconds. Count flashes for 30 seconds: About 40 flashes. Average battery current: A fraction of a milliamp.
No flashes: what should I check?
Check pin 1 and pin 8 power and that the LED is the right way round.
LED stays on: what should I check?
Pin 6 is not joined to pin 2 or the capacitor is not connected.
Very faint flash: what should I check?
Use a high-brightness LED or lengthen the flash with a larger RB.
Flashes too fast: what should I check?
Check RA is 100 kilohm and the capacitor is 10 microfarad.
