Projects / Hidden camera lens finder

Hidden camera lens finder

Beginner45 minGuided buildReviewed

Build it step by step

0 of 6 done
  1. 13.4 mA

    Plan the ring

    Make a hole in a card or the perfboard centre. Place six LEDs in a ring around it, pointing outwards.

  2. 13.4 mA

    Solder the LEDs and resistors

    Each LED gets its own 330 Ω resistor in series. Join all cathodes together.

  3. ++

    Add the battery and button

    Push button in series with the battery holder + wire, and cathodes to the battery holder -.

  4. 13.5 mA

    Add the viewing tube

    Roll a short black card tube to put your eye to the hole, so the LEDs light the scene but do not shine straight into your eye.

  5. 13.5 mA

    Scan a room

    Dim the room, switch on the LEDs, look through the hole and sweep slowly.

  6. Check a find

    A camera lens appears as a bright red dot. Check using your phone's camera and by looking at the object.

In short

How do you build a hidden camera lens finder?

A ring of red LEDs around a viewing tube lights up camera lenses, which shine back brightly when you look through the hole. You need LED 5 mm red × 6, Resistor 330 Ω × 6, Tactile push button 6 mm, Battery holder 2 × AA, AA alkaline battery × 2, Perfboard (dot PCB) 7 × 9 cm and Soldering iron 60 W (adjustable temperature). It takes 6 steps and about 45 minutes.

Level
Beginner
Time
About 45 min
Parts
7

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Battery holder +Push button, then to six resistors in parallelButton switches the supply
Each 330 Ω resistorIn series with one red LED anodeSets about 3 mA each
All LED cathodesBattery holder -Return
LEDsRing around the viewing holeMounted in a ring on the perfboard

No code needed

No code. A simple circuit: two 1.5 V AA cells give about 3 V. Each red LED drops about 2 V, so each 330 Ω resistor sets roughly 3 mA, and six LEDs draw about 18 mA.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Press the buttonAll six LEDs light
Look at a phone camera lens from 2 mA bright red dot shows
Look at a shiny screw or glassAlso reflects, so check the shape
Look at a dark wallNo dot

If it does not work

LEDs are dim

The cells are flat or one resistor is too high. Measure the battery.

Bright reflections everywhere

Shiny items such as bolts and glass reflect too, so check each dot's shape and the object.

Only some LEDs light

Check each LED's direction and solder joint.

Dot is hard to see

Dim the room and keep your eye close to the tube.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the hidden camera lens finder?

LED 5 mm red × 6, Resistor 330 Ω × 6, Tactile push button 6 mm, Battery holder 2 × AA, AA alkaline battery × 2, Perfboard (dot PCB) 7 × 9 cm and Soldering iron 60 W (adjustable temperature).

How long does the hidden camera lens finder take to build?

About 45 minutes for a beginner maker, in 6 steps.

How do I know the hidden camera lens finder works?

Press the button: All six LEDs light. Look at a phone camera lens from 2 m: A bright red dot shows. Look at a shiny screw or glass: Also reflects, so check the shape.

LEDs are dim: what should I check?

The cells are flat or one resistor is too high. Measure the battery.

Bright reflections everywhere: what should I check?

Shiny items such as bolts and glass reflect too, so check each dot's shape and the object.

Only some LEDs light: what should I check?

Check each LED's direction and solder joint.

Dot is hard to see: what should I check?

Dim the room and keep your eye close to the tube.